- 您現在的位置：買賣IC網 > PDF目錄374039 > ADUC702 (Analog Devices, Inc.) 5 AMP MINIATURE POWER RELAY PDF資料下載
參數資料
| 型號： | ADUC702 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 5 AMP MINIATURE POWER RELAY |
| 中文描述： | 精密模擬微控制器的12位模擬I / O，ARM7TDMI的微控制器 |
| 文件頁數： | 32/80頁 |
| 文件大小： | 840K |
| 代理商： | ADUC702 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
ADuC702x Series
Preliminary Technical Data
NONVOLATILE FLASH/EE MEMORY
FLASH/EE MEMORY OVERVIEW
Rev. PrB | Page 32 of 80
The ADuC702x incorporates Flash/EE memory technology on-
chip to provide the user with non-volatile, in-circuit
reprogrammable memory space.
Like EEPROM, Flash memory can be programmed in-system at
a byte level, although it must first be erased; the erase being
performed in page blocks. Thus, Flash memory is often and
more correctly referred to as Flash/EE memory.
Overall, Flash/EE memory represents a step closer to the ideal
memory device that includes non-volatility, in-circuit
programmability, high density, and low cost. Incorporated in
the ADuC702x, Flash/EE memory technology allows the user to
update program code space in-circuit, without the need to
replace one time programmable (OTP) devices at remote
operating nodes.
FLASH/EE MEMORY AND THE ADUC702X
The ADuC702x contains a 64 kByte array of Flash/EE Memory.
The lower 62 Kbytes is available to the user and the upper 2
kBytes of this Flash/EE program memory array contain
permanently embedded firmware, allowing in circuit serial
download. These 2 Kbytes of embedded firmware also contain a
power-on configuration routine that downloads factory
calibrated coefficients to the various calibrated peripherals
(ADC, temperature sensor, bandgap references and so on). This
2 kByte embedded firmware is hidden from user code.
The 62kBytes of Flash/EE memory can be programmed in-
circuit, using the serial download mode or the JTAG mode
provided or via parallel programming.
(1) Serial Downloading (In-Circuit Programming)
The ADuC702x facilitates code download via the standard
UART serial port or via the I2C port. The ADuC702x will enter
serial download mode after a reset or power cycle if the BM pin
is pulled low through an external 1kOhm resistor. Once in serial
download mode, the user can download code to the full
62kBytes of Flash/EE memory while the device is in circuit in
its target application hardware. A PC serial download
executable is provided as part of the development system for
serial downloading via the UART. An application note is
available at
www.analog.com/microconverter
describing the
protocol for serial downloading via the UART and I2C.
(2) Parallel Programming
The parallel programming protocol allows the on-chip Flash/EE
memory be programmed by industry standard third party
programmers.
(3) JTAG access
The JTAG protocol uses the on-chip JTAG interface to facilitate
code download and debug.
FLASH/EE MEMORY SECURITY
The 62kByte of Flash/EE memory available to the user can be
read and write protected.
Bit 31 of the FEEPRO/FEEHIDE MMR protects the 62kBytes
from being read through JTAG and also in parallel
programming mode. The other 31 bits of this register protect
writing to the flash memory, each bit protects 4 pages, i.e.
2kBytes. Write protection is activated for all type of access.
There are two levels of protection:
- Protection can be set and removed by writing directly into
FEEHIDE MMR.
- FEEPRO can be protected by a key to avoid direct access to
FEEPRO. The key is saved once and must be entered again to
modify FEEPRO. A mass erase will set the key back to 0xFFFF
but will also erase all the user code.
Sequence to write the key:
1. Enter an address in FEEADR.
2. Do a single READ command, wait for the read to be
successful by monitoring FEESTA.
3. Run a verify command.
4. Write the bit in FEEPRO corresponding to the page to be
protected.
5. Enable key protection by setting bits 7 to 4 of FEEMOD.
6. Write a 32 bit key in FEEADR, FEEDAT
7. Run the write key command 0x0C in FEECON, wait for the
read to be successful by monitoring FEESTA.
To remove or modify the protection the same sequence can be
used with a modified value of FEEPRO.
The sequence above is illustrated in the following example, this
protects writing pages 4 to 7 of the FLASH:
FEEADR = 0x800; //Any address,
FEECON=0x01; //Read command
while (!(FEESTA & 0x01)){} //Wait for read
FEECON=0x04; //Verify Command
FEEPRO=0xFFFFFFFD; //Protect pages 4 to 7
FEEMOD=(FEEMOD & 0xF0); //Write key enable
FEEADR=0xAA55; //16 bit key value
FEEDAT=0xAA55; //16 bit key value
FEECON= 0x0C; // Write key command
while (!(FEESTA & 0x01)){} //Wait for command
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC814ARU-REEL7 | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:37; Connector Shell Size:25; Connecting Termination:Crimp; Circular Shell Style:Jam Nut Receptacle; Body Style:Straight RoHS Compliant: No |
| ADUC814BRU | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:37; Connector Shell Size:25; Connecting Termination:Crimp; Circular Shell Style:Jam Nut Receptacle; Body Style:Straight RoHS Compliant: No |
| ADUC814BRU-REEL | Circular Connector; No. of Contacts:56; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:25-4 |
| ADUC814BRU-REEL7 | Circular Connector; No. of Contacts:61; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:25-61 |
| ADUC814 | MicroConverter, Small Package 12-Bit ADC with Embedded Flash MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC7020 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU |
| ADUC7020BCP62 | 制造商:Analog Devices 功能描述:FLASH ARM7+5-CH,12-B ADC & 4X12-B DAC IC - Trays |
| ADUC7020BCP62-U1 | 制造商:Analog Devices 功能描述:FLASH ARM7+5-CH,12-B ADC & 4X12-B DAC IC - Trays |
| ADUC7020BCPZ62 | 功能描述:IC MCU FLSH 62K ANLG I/O 40LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外圍設備:電容感應，DMA，LCD，POR，PWM，WDT 輸入/輸出數:25 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b，D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤 |
| ADUC7020BCPZ62I | 功能描述:IC MCU FLSH 62K ANLG I/O 40LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外圍設備:電容感應，DMA，LCD，POR，PWM，WDT 輸入/輸出數:25 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b，D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。