- 您現在的位置：買賣IC網 > PDF目錄385345 > GS9092 (Gennum Corporation) GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI PDF資料下載
參數資料
| 型號： | GS9092 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| 中文描述： | GS9092 GenLINX - R的第三270Mb / s的串行SDI和DVB - ASI在內 |
| 文件頁數： | 29/58頁 |
| 文件大小： | 608K |
| 代理商： | GS9092 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
GS9092 Data Sheet
28202 - 2
September 2005
29 of 58
Once the above steps are completed, the application layer may set the
ANC_PKT_INS bit of the IOPROC_DISABLE register HIGH (see
Table 3-4
in
Packet Generation and Insertion on page 35
) to enable insertion of the prepared
ancillary packets into the video data stream. Ancillary data packets will be inserted
in the following frame after the ANC_PKT_INS bit has been set HIGH.
NOTE: When inserting ancillary data into the blanking region, the total number of
words cannot exceed the size of the blanking region, and the data count value in
the packet must be correct.
3.3.3.1 Ancillary Data Insertion
Once the ANC_PKT_INS bit is set HIGH, the device will start reading the user
programmed ancillary packets out of the FIFO and insert them into the video
stream. Subsequent ancillary packets programmed by the application layer will
continue to be placed into the first half of the FIFO until the ANC_DATA_SWITCH
bit is toggled (see block A of
Figure 3-7
).
By default, the ANC_DATA_SWITCH bit of the IO_CONFIG register is set LOW.
When ANC_DATA_SWITCH is toggled from LOW to HIGH, any new ancillary data
the application layer programs will be placed in the second half of the FIFO. The
device will continue to insert ancillary data from the first half of the FIFO into the
video stream (see block B of
Figure 3-7
).
Once the ancillary data in the first half of the FIFO has been inserted into the video
stream, ANC_DATA_SWITCH may be toggled again. This will clear the first half of
the FIFO and begin insertion of ancillary data from the second half of the FIFO. The
application layer may continue programming ancillary data into the second half of
the FIFO (see block C of
Figure 3-7
).
If the ANC_DATA_SWITCH bit is toggled again, any new data the application layer
programs will be placed into the first half of the FIFO. The device will continue to
insert ancillary data from the second half of the FIFO into the video stream (see
block D of
Figure 3-7
).
Toggling ANC_DATA_SWITCH again will clear the second half of the FIFO and
restore the read and write pointers to the situation shown in block A. The switching
process (shown in blocks A to D in
Figure 3-7
) will continue with each toggle of the
ANC_DATA_SWITCH bit.
NOTE: At least 1100 PCLK cycles (41us) must pass between toggles of the
ANC_DATA_SWITCH bit.
The GS9092 will insert the ancillary data programmed in the FIFO into each video
frame at the designated line(s) programmed in ANC_LINE_A[10:0] and/or
ANC_LINE_B[10:0].
Clearing the ANC_PKT_INS bit will not automatically disable ancillary data
insertion. To disable ancillary data insertion, switch the FIFO into bypass mode by
setting FIFO_MODE[1:0] = 11b. 2200 PCLK cycles after the device re-enters
ancillary data insertion mode, data extraction will commence immediately if
ANC_PKT_INS is HIGH.
相關PDF資料 |
PDF描述 |
|---|---|
| GS9092-CNE3 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GSC9620 | P-CHANNEL ENHANCEMENT MODE POWER MOSFET |
| GSD2004S-V-GS08 | DIODE 0.225 A, 300 V, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB, ROHS COMPLIANT, PLASTIC PACKAGE-3, Signal Diode |
| GSD2004S-V-GS18 | DIODE 0.225 A, 300 V, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB, ROHS COMPLIANT, PLASTIC PACKAGE-3, Signal Diode |
| GSD2004W-V-GS18 | DIODE 0.225 A, 300 V, SILICON, SIGNAL DIODE, ROHS COMPLIANT, PLASTIC PACKAGE-2, Signal Diode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9092A | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092A_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092ACNE3 | 功能描述:RF, RFID, WIRELESS RoHS:是 類別:集成電路 (IC) >> 接口 - 串行器，解串行器 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 功能:解串器 數據速率:2.5Gbps 輸入類型:串行 輸出類型:并聯 輸入數:- 輸出數:24 電源電壓:1.8 V ~ 3.3 V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:管件 |
| GS9092ACNTE3 | 制造商:Semtech Corporation 功能描述:270Mb/s Transmitter for SDI & ASI |
| GS9092CNE3 | 制造商:Gennum Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。