- 您現在的位置：買賣IC網 > PDF目錄385345 > GS9092 (Gennum Corporation) GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI PDF資料下載
參數資料
| 型號： | GS9092 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| 中文描述： | GS9092 GenLINX - R的第三270Mb / s的串行SDI和DVB - ASI在內 |
| 文件頁數： | 30/58頁 |
| 文件大小： | 608K |
| 代理商： | GS9092 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
GS9092 Data Sheet
28202 - 2
September 2005
30 of 58
When there are existing ancillary data packets present in the video data stream,
the device will append the ancillary data to the existing data only when the
ANC_SAV bit is set LOW. In this case, all existing ancillary data must be
contiguous after the EAV. If data is not contiguous, the ancillary data to be inserted
will be written at the first available space where the video is set to blanking levels.
When ANC_SAV is set HIGH, any data present after the SAV will be overwritten.
To overwrite existing ancillary data, the ANC_DATA_REPLACE bit of the
FIFO_EMPTY_OFFSET register must be set HIGH. When this bit is set HIGH,
existing ancillary data will be replaced with the data to be inserted and the
remainder of the line will be set to blanking levels. The device will replace ancillary
data on the line of insertion only. Existing ancillary data on other lines will not be
replaced with blanking levels.
NOTE: If the ANC_SAV and ANC_DATA_REPLACE bits are both set HIGH, and
if ancillary data is inserted on an active picture line, the remainder of the active line
will be set to blanking levels.
Ancillary Data Readback Mode
By default, when the FIFO is in ancillary data insertion mode, the application layer
can only write ancillary data into the FIFO. However, if ANC_DATA_RDBACK is
set HIGH (bit 13 of address 06h), the GS9092 will discontinue inserting ancillary
data into the data stream and the host interface may read the ancillary data
programmed into that half of the FIFO.
3.3.3.2 Clearing the ANC Data FIFO
When switching to ANC FIFO mode, the user must follow one of the 2 methods
below to ensure that the FIFO is fully cleared.
Clearing ANC FIFO Method 1:
1. Enable ANC FIFO mode (write 10b into the FIFO_MODE register).
2. Wait for ANC_FIFO_READY bit to be asserted.
3. Toggle (LOW-to-HIGH-to-LOW) ANC_DATA_SWITCH bit (bit 12 of
IO_CONFIG register) twice.
Clearing ANC FIFO Method 2:
1. Power on device.
2. Set FIFO_EN pin HIGH.
3. Enable ANC FIFO mode (write 10b into the FIFO_MODE register).
4. Set FIFO_EN pin LOW.
5. Set FIFO_EN pin HIGH.
相關PDF資料 |
PDF描述 |
|---|---|
| GS9092-CNE3 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GSC9620 | P-CHANNEL ENHANCEMENT MODE POWER MOSFET |
| GSD2004S-V-GS08 | DIODE 0.225 A, 300 V, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB, ROHS COMPLIANT, PLASTIC PACKAGE-3, Signal Diode |
| GSD2004S-V-GS18 | DIODE 0.225 A, 300 V, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB, ROHS COMPLIANT, PLASTIC PACKAGE-3, Signal Diode |
| GSD2004W-V-GS18 | DIODE 0.225 A, 300 V, SILICON, SIGNAL DIODE, ROHS COMPLIANT, PLASTIC PACKAGE-2, Signal Diode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9092A | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092A_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092ACNE3 | 功能描述:RF, RFID, WIRELESS RoHS:是 類別:集成電路 (IC) >> 接口 - 串行器，解串行器 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 功能:解串器 數據速率:2.5Gbps 輸入類型:串行 輸出類型:并聯 輸入數:- 輸出數:24 電源電壓:1.8 V ~ 3.3 V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:管件 |
| GS9092ACNTE3 | 制造商:Semtech Corporation 功能描述:270Mb/s Transmitter for SDI & ASI |
| GS9092CNE3 | 制造商:Gennum Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。