- 您現在的位置：買賣IC網 > PDF目錄385345 > GS9092ACNE3 (Gennum Corporation) GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI PDF資料下載
參數資料
| 型號： | GS9092ACNE3 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| 中文描述： | GS9092A GenLINX - R的第三270Mb / s的串行SDI和DVB - ASI在內 |
| 文件頁數： | 23/59頁 |
| 文件大小： | 614K |
| 代理商： | GS9092ACNE3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
GS9092A Data Sheet
34715 - 0
February 2006
23 of 59
3.3.1 Video Mode
The internal FIFO is in video mode under the following conditions:
the FIFO_EN and IOPROC_EN pins are set HIGH,
the FIFO_MODE[1:0] bits in the IOPROC_DISABLE register (
Table 3-4
) are
configured to 00b,
the DETECT_TRS pin is set LOW; and
TRS insertion, EDH correction/insertion, illegal code re-mapping, and SMPTE
packet insertion are all disabled (i.e. bits 0, 2, 3, and 4 of the
IOPROC_DISABLE register are set HIGH).
NOTE: The FIFO will still enter video mode if any of bits 0, 2, 3, or 4 of the
IOPROC_DISABLE register are LOW; however, the output video data will contain
errors.
By default, the FIFO_MODE[1:0] bits are set to 00b by the device whenever the
SMPTE_BYPASS pin is set HIGH and the DVB_ASI and DETECT_TRS pins are
set LOW.
In video mode, the H, V, and F pins become input signals that must be supplied by
the user.
Figure 3-2
shows the input and output signals of the FIFO when it is configured for
video mode.
Figure 3-2: FIFO in Video Mode
When operating in video mode, the GS9092A will read data sequentially from the
FIFO, starting with the first active pixel in location zero of the memory. In this mode,
it is possible to use the FIFO for clock phase interchange and data delay.
The device will ensure read-side synchronization is maintained, according to the
supplied PCLK and supplied H, V, and F timing information.
Full write-control of the FIFO is made available to the application interface such
that data is clocked into the FIFO on the rising edge of the externally provided
WR_CLK. The FIFO write pointer will be reset to position zero of the memory when
there is a HIGH-to-LOW transition at the WR_RESET pin.
WR_CLK
FIFO
(Video Mode)
RD_CLK (PCLK)
10-bit Video Data
10-bit Video Data
WR_RESET
RD_RESET
(supplied H timing)
Application Interface
Internal
相關PDF資料 |
PDF描述 |
|---|---|
| GS9092 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092-CNE3 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GSC9620 | P-CHANNEL ENHANCEMENT MODE POWER MOSFET |
| GSD2004S-V-GS08 | DIODE 0.225 A, 300 V, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB, ROHS COMPLIANT, PLASTIC PACKAGE-3, Signal Diode |
| GSD2004S-V-GS18 | DIODE 0.225 A, 300 V, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB, ROHS COMPLIANT, PLASTIC PACKAGE-3, Signal Diode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9092ACNTE3 | 制造商:Semtech Corporation 功能描述:270Mb/s Transmitter for SDI & ASI |
| GS9092CNE3 | 制造商:Gennum Corporation 功能描述: |
| GS9092-CNE3 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Gennum Corporation 功能描述: |
| GS90A12-P1M | 功能描述:插入式交流適配器 80W 12V 6.67A RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓（通道 1）:5 V 輸出電流（通道 1）:1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V |
| GS90A15-P1M | 功能描述:插入式交流適配器 90W 15V 6A RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓（通道 1）:5 V 輸出電流（通道 1）:1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V |
發布緊急采購，3分鐘左右您將得到回復。