欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: IS42LS81600A-7TI
英文描述: 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
中文描述: 16Meg × 8,8Meg x16
文件頁數: 31/66頁
文件大小: 556K
代理商: IS42LS81600A-7TI
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
ADVANCED INFORMATION
Rev. 00A
06/01/02
31
ISSI
IS42S81600A, IS42S16800A, IS42S32400A
IS42LS81600A, IS42LS16800A, IS42LS32400A
DON'T CARE
UNDEFINED
CLK
COMMAND
DQ
READ
NOP
NOP
NOP
CAS Latency - 3
t
AC
t
OH
D
OUT
T0
T1
T2
T3
T4
t
LZ
CLK
COMMAND
DQ
READ
NOP
NOP
CAS Latency - 2
t
AC
t
OH
D
OUT
T0
T1
T2
T3
t
LZ
CAS LATENCY
CAS Latency
The CAS latency is the delay, in clock cycles, between the
registration of a READ command and the availability of the
first piece of output data. The latency can be set to two or
three clocks.
If a READ command is registered at clock edge n, and the
latency is
m
clocks, the data will be available by clock edge
n +
m. The DQs will start driving as a result of the clock edge
one cycle earlier
(n + m
- 1), and provided that the relevant
access times are met, the data will be valid by clock edge
n +
m. For example, assuming that the clock cycle time is
such that all relevant access times are met, if a READ
command is registered at T0 and the latency is programmed
to two clocks, the DQs will start driving after T1 and the data
will be valid by T2, as shown in CAS Latency diagrams. The
Allowable Operating Frequency table indicates the operat-
ing frequencies at which each CAS latency setting can be
used.
Reserved states should not be used as unknown operation or
incompatibility with future versions may result.
Operating Mode
The normal operating mode is selected by setting M7 and M8
to zero; the other combinations of values for M7 and M8 are
CAS Latency
Allowable Operating Frequency (MHz)
Speed
CAS Latency = 2
CAS Latency = 3
7.5
100
133
10
75
100
reserved for future use and/or test modes. The programmed
burst length applies to both READ and WRITE bursts.
Test modes and reserved states should not be used
because unknown operation or incompatibility with future
versions may result.
Write Burst Mode
When M9 = 0, the burst length programmed via M0-M2
applies to both READ and WRITE bursts; when M9 = 1, the
programmed burst length applies to READ bursts, but write
accesses are single-location (nonburst) accesses.
相關PDF資料
PDF描述
IS42S16800A 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S16800A-7B 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S16800A-7BI 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S16800A-7T 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S16800A-7TI 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
相關代理商/技術參數
參數描述
IS42R16100E-7TL 制造商:Integrated Silicon Solution Inc 功能描述:
IS42R16320D-7BL 制造商:Integrated Silicon Solution Inc 功能描述:
IS42R16320D-7BLI 制造商:Integrated Silicon Solution Inc 功能描述:DRAM Chip SDRAM 512M-Bit 32Mx16 2.5V 54-Pin TFBGA
IS42RM16160D-7BL 功能描述:動態隨機存取存儲器 256M (16Mx16) 143MHz Mobile S動態隨機存取存儲器, 2.5v RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube
IS42RM16160D-7BLI 功能描述:動態隨機存取存儲器 256M (16Mx16) 143MHz Mobile S動態隨機存取存儲器, 2.5v RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube
主站蜘蛛池模板: 延津县| 安西县| 嘉峪关市| 根河市| 廉江市| 乌拉特后旗| 安达市| 喀喇| 南丹县| 吉首市| 汤原县| 获嘉县| 柞水县| 波密县| 余江县| 互助| 林州市| 吴桥县| 博爱县| 环江| 南安市| 荃湾区| 德惠市| 高台县| 敖汉旗| 宁波市| 丹巴县| 治县。| 清镇市| 怀柔区| 芮城县| 兖州市| 广安市| 桂平市| 林州市| 磐安县| 临泽县| 灵川县| 鹤壁市| 综艺| 周至县|