欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數(shù)資料
型號: IS42S32400A-10TI
廠商: INTEGRATED SILICON SOLUTION INC
元件分類: DRAM
英文描述: CABLE ASSEMBLY; BNC MALE TO BNC FEMALE BULKHEAD; 50 OHM, RG174A/U COAX; ; *USES STANDARD 50 OHM INTERFACE CONNECTORS*
中文描述: 4M X 32 SYNCHRONOUS DRAM, 7 ns, PDSO86
封裝: PLASTIC, TSOP2-86
文件頁數(shù): 31/66頁
文件大小: 556K
代理商: IS42S32400A-10TI
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
ADVANCED INFORMATION
Rev. 00A
06/01/02
31
ISSI
IS42S81600A, IS42S16800A, IS42S32400A
IS42LS81600A, IS42LS16800A, IS42LS32400A
DON'T CARE
UNDEFINED
CLK
COMMAND
DQ
READ
NOP
NOP
NOP
CAS Latency - 3
t
AC
t
OH
D
OUT
T0
T1
T2
T3
T4
t
LZ
CLK
COMMAND
DQ
READ
NOP
NOP
CAS Latency - 2
t
AC
t
OH
D
OUT
T0
T1
T2
T3
t
LZ
CAS LATENCY
CAS Latency
The CAS latency is the delay, in clock cycles, between the
registration of a READ command and the availability of the
first piece of output data. The latency can be set to two or
three clocks.
If a READ command is registered at clock edge n, and the
latency is
m
clocks, the data will be available by clock edge
n +
m. The DQs will start driving as a result of the clock edge
one cycle earlier
(n + m
- 1), and provided that the relevant
access times are met, the data will be valid by clock edge
n +
m. For example, assuming that the clock cycle time is
such that all relevant access times are met, if a READ
command is registered at T0 and the latency is programmed
to two clocks, the DQs will start driving after T1 and the data
will be valid by T2, as shown in CAS Latency diagrams. The
Allowable Operating Frequency table indicates the operat-
ing frequencies at which each CAS latency setting can be
used.
Reserved states should not be used as unknown operation or
incompatibility with future versions may result.
Operating Mode
The normal operating mode is selected by setting M7 and M8
to zero; the other combinations of values for M7 and M8 are
CAS Latency
Allowable Operating Frequency (MHz)
Speed
CAS Latency = 2
CAS Latency = 3
7.5
100
133
10
75
100
reserved for future use and/or test modes. The programmed
burst length applies to both READ and WRITE bursts.
Test modes and reserved states should not be used
because unknown operation or incompatibility with future
versions may result.
Write Burst Mode
When M9 = 0, the burst length programmed via M0-M2
applies to both READ and WRITE bursts; when M9 = 1, the
programmed burst length applies to READ bursts, but write
accesses are single-location (nonburst) accesses.
相關PDF資料
PDF描述
IS42S32400A-10TL CABLE ASSEMBLY; SMA MALE RIGHT ANGLE TO; SMA FEMALE BULKHEAD; 50 OHM, PE-SR405FL (.085" RE-SHAPABLE); 18" CABLE LENGTH;
IS42S32400A-10TLI 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S16800A 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S16800A-6T 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S16800A-6TL 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
相關代理商/技術參數(shù)
參數(shù)描述
IS42S32400A-10TL 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S32400A-10TLI 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S32400A-6T 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S32400A-6TL 制造商:Integrated Silicon Solution Inc 功能描述:
IS42S32400A-6T-TR 制造商:Integrated Silicon Solution Inc 功能描述:DRAM Chip SDRAM 128M-Bit 4Mx32 3.3V 86-Pin TSOP-II T/R
主站蜘蛛池模板: 乡城县| 奉化市| 林甸县| 达孜县| 龙泉市| 潢川县| 城固县| 邢台县| 久治县| 施秉县| 宁明县| 淄博市| 山阴县| 景东| 梁平县| 缙云县| 正安县| 江西省| 察哈| 庆云县| 察隅县| 普兰店市| 清原| 巴青县| 同德县| 余姚市| 黎川县| 武冈市| 雷州市| 榕江县| 临颍县| 平乐县| 巴塘县| 枣庄市| 盖州市| 屯门区| 贵州省| 罗源县| 磴口县| 玉溪市| 扎鲁特旗|