- 您現在的位置：買賣IC網 > PDF目錄30737 > LC89057W-VF4-E SPECIALTY CONSUMER CIRCUIT, PQFP48 PDF資料下載
參數資料
| 型號： | LC89057W-VF4-E |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| 封裝： | 7 X 7 MM, SQFP-48 |
| 文件頁數： | 11/61頁 |
| 文件大小： | 355K |
| 代理商： | LC89057W-VF4-E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
LC89057W-VF4-E
No. 7202-19/61
8.2 Bi-Phase Signal Input/Output
8.2.1 Bi-phase signal input reception range
The input data reception range depends on the PLL lock frequency setting done with PLLSEL. The relationship
between this setting and the guaranteed reception range is shown below.
Table 8.4. Relationship between PLL Output Clock Setting and Reception Range (FSLIM0,1 = 0)
PLL Output Clock Setting
Input Data Reception Range
512fs (PLLSEL = 0)
28kHz to 105kHz
256fs (PLLSEL = 1)
28kHz to 195kHz
The fs reception range for input data within the above PLL output clock setting range can be controlled. This setting
is performed with FSLIM0,1. When this function is used, input data that exceeds the setting range is considered as
an error and the clock source is automatically switched to the XIN source and RDATA output data is according to
the RDTSEL setting.
8.2.2 Bi-phase signal input/output pins (RX0 to RX6, RXOUT)
There are 7 digital data input pins. Moreover, data modulated with the modulation function can also be selected and
thus selection from among 8 signals including this signal is possible. However, the pins that can be selected is
restricted by the setting conditions.
(1) The six pins RX0 and RX2 to RX6 are TTL level input pins with 5V input level tolerable.
(2) RX1 is a coaxial-compatible input pin with built-in amplifier that can receive up to 200mVp-p data.
The demodulation input and RXOUT output signals can each be selected independently.
(1) The demodulation data is selected with RISEL0 to 2.
(2) The RXOUT output data is selected with ROSEL0 to 2.
RXOUT can be muted with RXOFF. Muting is recommended when not using RXOUT in order to reduce clock
jitter.
The data input status can be monitored with the RXMON setting. The status of each data input pin is stored in CCB
address 0xEA and output registers DO0 to DO7. Since this function uses the XIN clock, the oscillation amplifier
must be set to the continuous operation mode when RXMON is set.
Demodulation input pin switching can be performed via PLL unlock with the ULSEL setting. As a result, data
switching can be accurately communicated to peripheral devices.
The interval from pin switching through RISEL0 to 2 until data is received is about 250
s to 350s. This function
also requires that the oscillation amplifier be set to the continuous operation mode.
Input pin selection
Internal supply signal
RX0
RX2
RX3
RX1
RX0
RX2
RX3
RX1
250
s to 350 s
Figure 8.5. Input Pin Selection Processing via PLL Unlock
相關PDF資料 |
PDF描述 |
|---|---|
| LC89057W-VF4A-E | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC89057W-VF4 | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC89058W-E | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC89058W-E | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC8905V | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC89058W | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Digital Audio Interface Receiver |
| LC89058WA-E | 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝: |
| LC89058W-E | 功能描述:音頻 DSP AUDIO INTERFACE RECEIVER RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| LC8905V | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Digital Audio Interface Receiver |
| LC89060 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:6-Bit Video D/A Converters |
發布緊急采購，3分鐘左右您將得到回復。