欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68C912B32CFU8
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 16-Bit Microcontroller
中文描述: 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP80
封裝: QFP-80
文件頁數: 41/128頁
文件大小: 748K
代理商: MC68C912B32CFU8
MC68HC912B32
MC68HC912B32TS/D
MOTOROLA
41
the longest possible life expectancy. This method requires stopping the program/erase sequence at pe-
riods of t
PPULSE
(t
EPULSE
for erasing) to determine if the Flash EEPROM is programmed/erased. After
the location reaches the proper value, it must continue to be programmed/erased with additional margin
pulses to ensure that it will remain programmed/erased. Failure to provide the margin pulses could lead
to corrupted or unreliable data.
Program/Erase Sequence
— To begin a program or erase sequence the external V
FP
voltage must
be applied and stabilized. The ERAS bit must be set or cleared, depending on whether a program se-
quence or an erase sequence is to occur. The LAT bit will be set to cause any subsequent data written
to a valid address within the Flash EEPROM to be latched into the programming address and data latch-
es. The next Flash array write cycle must be either to the location that is to be programmed if a pro-
gramming sequence is being performed, or, if erasing, to any valid Flash EEPROM array location.
Writing the new address and data information to the Flash EEPROM is followed by assertion of ENPE
to turn on the program/erase voltage to program/erase the new location(s). The LAT bit must be assert-
ed and the address and data latched to allow the setting of the ENPE control bit. If the data and address
have not been latched, an attempt to assert ENPE will be ignored and ENPE will remain negated after
the write cycle to FEECTL is completed. The LAT bit must remain asserted and the ERAS bit must re-
main in its current state as long as ENPE is asserted. A write to the LAT bit to clear it while ENPE is set
will be ignored. That is, after the write cycle, LAT will remain asserted. Likewise, an attempt to change
the state of ERAS will be ignored and the state of the ERAS bit will remain unchanged.
The programming software is responsible for all timing during a program sequence. This includes the
total number of program pulses (n
PP
), the length of the program pulse (t
PPULSE
), the program margin
pulses (p
m
) and the delay between turning off the high voltage and verifying the operation (t
VPROG
).
The erase software is responsible for all timing during an erase sequence. This includes the total num-
ber of erase pulses (e
m
), the length of the erase pulse (t
EPULSE
), the erase margin pulse or pulses, and
the delay between turning off the high voltage and verifying the operation (t
VERASE
).
Software also controls the supply of the proper program/erase voltage to the V
FP
pin, and should be at
the proper level before ENPE is set during a program/erase sequence.
A program/erase cycle should not be in progress when starting another program/erase, or while at-
tempting to read from the array.
NOTE
Although clearing ENPE disables the program/erase voltage (V
FP
) from the V
FP
pin to the array, care must be taken to ensure that V
FP
is at V
DD
whenever pro-
gramming/erasing is not in progress. Not doing so could damage the part. Ensuring
that V
FP
is always greater or equal to V
DD
can be accomplished by controlling the
V
FP
power supply with the programming software via an output pin. Alternatively,
all programming and erasing can be done prior to installing the device on an appli-
cation circuit board which can always connect V
FP
to V
DD
. Programming can also
be accomplished by plugging the board into a special programming fixture which
provides program/erase voltage to the V
FP
pin.
相關PDF資料
PDF描述
MC68CK338 Highly Integrated, Low-Power, 32-Bit Microcontroller
MC68EC060 32-Bit Microprocessors.(32位微處理器)
MC68EN360RC25V QUad Integrated Communications Controller Users Manual
MC68EN360CFE25 QUad Integrated Communications Controller Users Manual
MC68EN360FE25 AC 4C 4#12 PIN PLUG 023
相關代理商/技術參數
參數描述
MC68C912B32FU8 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller
MC68CK16Z1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
MC68CK16Z1CAG16 功能描述:16位微控制器 - MCU 16BIT 1KRAM 32KHZ CRYSTAL RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MC68CK16Z1CAG16 制造商:Freescale Semiconductor 功能描述:Microcontroller
MC68CK16Z1CFC16 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
主站蜘蛛池模板: 麻栗坡县| 阿勒泰市| 铜陵市| 嵩明县| 原平市| 连州市| 亳州市| 潍坊市| 南安市| 临城县| 新密市| 乌兰浩特市| 高碑店市| 台北县| 桑植县| 洪洞县| 安阳市| 集贤县| 和田市| 兴安盟| 苍溪县| 博湖县| 炎陵县| 新和县| 定兴县| 远安县| 丽江市| 荣昌县| 克拉玛依市| 喀喇沁旗| 梅河口市| 岱山县| 华安县| 房产| 西充县| 上饶县| 蚌埠市| 兴义市| 都兰县| 伊川县| 宕昌县|