- 您現在的位置：買賣IC網 > PDF目錄382369 > P87LPC760 (NXP Semiconductors N.V.) Low power, low price, low pin count (14 pin) microcontroller with 1 kbyte OTP PDF資料下載
參數資料
| 型號： | P87LPC760 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Low power, low price, low pin count (14 pin) microcontroller with 1 kbyte OTP |
| 中文描述： | 低功耗，低價格，低引腳數（14針），1字節檢察官辦公室微控制器 |
| 文件頁數： | 17/56頁 |
| 文件大?。?/td> | 290K |
| 代理商： | P87LPC760 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
Philips Semiconductors
Preliminary data
P87LPC760
Low power, low price, low pin count (14 pin)
microcontroller with 1 kbyte OTP
2002 Mar 07
14
BIT
I2CFG.7
SYMBOL
SLAVEN
FUNCTION
Slave Enable. Writing a 1 this bit enables the slave functions of the I
2
C subsystem. If SLAVEN and
MASTRQ are 0, the I
2
C hardware is disabled. This bit is cleared to 0 by reset and by an I
2
C
time-out.
Master Request. Writing a 1 to this bit requests mastership of the I
2
C bus. If a transmission is in
progress when this bit is changed from 0 to 1, action is delayed until a stop condition is detected. A
start condition is sent and DRDY is set (thus making ATN = 1 and generating an I
2
C interrupt).
When a master wishes to release mastership status of the I
2
C, it writes a 1 to XSTP in I2CON.
MASTRQ is cleared by an I
2
C time-out.
Writing a 1 to this bit clears the Timer I overflow flag. This bit position always reads as a 0.
Writing a 1 to this bit lets Timer I run; a zero stops and clears it. Together with SLAVEN, MASTRQ,
and MASTER, this bit determines operational modes as shown in Table 1.
Reserved for future use. Should not be set to 1 by user programs.
These two bits are programmed as a function of the CPU clock rate, to optimize the MIN HI and LO
time of SCL when this device is a master on the I
2
C. The time value determined by these bits
controls both of these parameters, and also the timing for stop and start conditions.
I2CFG.6
MASTRQ
I2CFG.5
I2CFG.4
CLRTI
TIRUN
I2CFG.2, 3
I2CFG.1, 0 CT1, CT0
—
CT0
SU01552
CT1
—
—
TIRUN
CLRTI
MASTRQ
SLAVEN
0
1
2
3
4
5
6
7
I2CFG
Reset Value: 00h
Bit Addressable
Address: C8h
Figure 8. I
2
C Configuration Register (I2CFG)
Regarding Software Response Time
Because the P87LPC760 can run at 20 MHz, and because the I
2
C
interface is optimized for high-speed operation, it is quite likely that
an I
2
C service routine will sometimes respond to DRDY (which is set
at a rising edge of SCL) and write I2DAT before SCL has gone low
again. If XDAT were applied directly to SDA, this situation would
produce an I
2
C protocol violation. The programmer need not worry
about this possibility because XDAT is applied to SDA only when
SCL is low.
Conversely, a program that includes an I
2
C service routine may take
a long time to respond to DRDY. Typically, an I
2
C routine operates
on a flag-polling basis during a message, with interrupts from other
peripheral functions enabled. If an interrupt occurs, it will delay the
response of the I
2
C service routine. The programmer need not worry
about this very much either, because the I
2
C hardware stretches the
SCL low time until the service routine responds. The only constraint
on the response is that it must not exceed the Timer I time-out.
Values to be used in the CT1 and CT0 bits are shown in Table 2. To
allow the I
2
C bus to run at the maximum rate for a particular
oscillator frequency, compare the actual oscillator rate to the f OSC
max column in the table. The value for CT1 and CT0 is found in the
first line of the table where CPU clock max is greater than or equal
to the actual frequency.
Table 2 also shows the machine cycle count for various settings of
CT1/CT0. This allows calculation of the actual minimum high and
low times for SCL as follows:
SCL min high/low time in microseconds =CPU clock in MHz
For instance, at an 8 MHz frequency, with CT1/CT0 set to 1 0, the
minimum SCL high and low times will be 5.25
μ
s.
Table 2 also shows the Timer I timeout period (given in machine
cycles) for each CT1/CT0 combination. The timeout period varies
because of the way in which minimum SCL high and low times are
measured. When the I
2
C interface is operating, Timer I is pre-loaded
at every SCL transition with a value dependent upon CT1/CT0. The
pre-load value is chosen such that a minimum SCL high or low time
has elapsed when Timer I reaches a count of 008 (the actual value
pre-loaded into Timer I is 8 minus the machine cycle count).
相關PDF資料 |
PDF描述 |
|---|---|
| P87LPC761 | Low power, low price, low pin count (16 pin) microcontroller with 2 kbyte OTP |
| P87LPC762 | Low power, low price, low pin count 20 pin microcontroller with 2 kbyte OTP |
| P87LPC768 | Low Power, Low System Cost 80C51 MCU with ADC and PWM |
| P87LPC768BN | Low Power, Low System Cost 80C51 MCU with ADC and PWM |
| P88-3004 | TONER VACUUM STD 220/240V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P87LPC760BDH | 功能描述:8位微控制器 -MCU 80C51 1K/128 OTP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P87LPC760BDH,112 | 功能描述:8位微控制器 -MCU 80C51 1K/128 OTP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P87LPC760BDH,118 | 功能描述:8位微控制器 -MCU 14 PIN MCU 1KBYTE OTP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P87LPC760BN | 功能描述:8位微控制器 -MCU 1K/128 OTP 2.7-6V COMM DIP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P87LPC760BN,112 | 功能描述:8位微控制器 -MCU 1K/128 OTP 2.7-6V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。