- 您現在的位置：買賣IC網 > PDF目錄98238 > TLC320AC01CPM (TEXAS INSTRUMENTS INC) SPECIALTY ANALOG CIRCUIT, PQFP64 PDF資料下載
參數資料
| 型號： | TLC320AC01CPM |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 封裝： | PLASTIC, QFP-64 |
| 文件頁數： | 18/93頁 |
| 文件大小： | 601K |
| 代理商： | TLC320AC01CPM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁
2–12
2.14.1.2 Frame-Sync Delayed (FSD), Master Mode
For the master, the frame-sync delayed output occurs 1/2 shift-clock period ahead of FS to compensate for
the time delay through the master and slave devices. The timing relationships are as follows:
1.
When the FSD register data is 0, then FSD goes low on the falling edge of SCLK prior to the rising
edge of SCLK when FS goes low (see Figure 4 – 4).
2.
When the FSD register data is greater than 17, then FSD goes low on a rising edge of SCLK that
is the FSD register number of SCLKs after the falling edge of FS.
Register data values from 1 to 17 should not be used.
2.14.1.3 Frame Sync (FS), Slave Mode
The frame-sync timing is generated externally, applied to FS, and controls the ADC and DAC timing (see
Subsection 2.15.4). The external frame-sync width must be a minimum of one shift clock to be recognized
and can remain low until the next data frame is required.
2.14.1.4 Frame-Sync Delayed (FSD), Slave Mode
This output is fed from the master to the first slave and the first slave FSD output to the second and so on
down the chain. The FSD timing sequence in the slave mode is as follows:
1.
When the FSD register data is 0, then FSD goes low after FS goes low (see Figure 4 – 5).
2.
When the FSD register data is greater than 17, FSD goes low on a rising edge of SCLK that is
the FSD register number of SCLKs after the falling edge of FS.
Data values from 1 to 17 should not be used.
2.14.2
Data Out (DOUT)
DOUT is placed in the high-impedance state on the seventeenth rising edge of SCLK (internal or external)
after the falling edge of frame sync. In the primary communication, the data word is the ADC conversion
result. In the secondary communication, the data is the register read results when requested by the
read/write (R/W) bit with the eight MSBs set to 0 (see Section 2.16). If no register read is requested, the
secondary word is all zeroes.
2.14.2.1 Data Out, Master Mode
In the master mode, DOUT is taken from the high-impedance state by the falling edge of frame sync. The
most significant data bit then appears on DOUT.
2.14.2.2 Data Out, Slave Mode
In the slave mode, DOUT is taken from the high-impedance state by the falling edge of the external frame
sync or the rising edge of the external SCLK, whichever occurs first (see Figure 4 – 7). The falling edge of
frame sync can occur
±1/4 SCLK period around the SCLK rising edge (see Figure 4–3). The most
significant data bit then appears on DOUT.
2.14.3
Data In (DIN)
In the primary communication, the data word is the digital input signal to the DAC channel. In the secondary
communication, the data is the control and configuration data to set up the device for a particular function
(see Section 2.16).
2.14.4
Hardware Program Terminals (FC1 and FC0)
These inputs provide for hardware programming requests for secondary communication or phase
adjustment. These inputs work in conjunction with the control bits D01 and D00 of the primary data word
or control bits DS15 and DS14 of the secondary data word. The data on FC1 and FC0 are latched on the
rising edge of the next internally generated primary or secondary frame-sync interval. These inputs should
be tied low if not used (see Section 2.17 and Table 2–3).
相關PDF資料 |
PDF描述 |
|---|---|
| TLC320AC01CFN | SPECIALTY ANALOG CIRCUIT, PQCC28 |
| TLC320AC02IFN | SPECIALTY ANALOG CIRCUIT, PQCC28 |
| TLC320AC02CPMR | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| TLC320AC02IPM | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| TLC320AC02IFNR | SPECIALTY ANALOG CIRCUIT, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC320AC01CPMR | 功能描述:接口—CODEC Single Ch Codec-BW RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| TLC320AC02 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Single-Supply Analog Interface Circuit |
| TLC320AC02C | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Single-Supply Analog Interface Circuit |
| TLC320AC02CFN | 功能描述:接口—CODEC SNGL CH Codec Bandwidth Indpendent RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| TLC320AC02CFNR | 功能描述:接口—CODEC SNGL CH Codec Bandwidth Indpendent RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。