- 您現在的位置：買賣IC網 > PDF目錄98265 > TMC222-PI20 STEPPER MOTOR CONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | TMC222-PI20 |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, PDSO20 |
| 封裝： | SOIC-20 |
| 文件頁數： | 24/48頁 |
| 文件大小： | 457K |
| 代理商： | TMC222-PI20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
30
TMC222 DATASHEET (V. 1.12 / March 7, 2011)
Copyright 2004-2011 TRINAMIC Motion Control GmbH & Co. KG
6.8
Command Description
There are data fields labeled as "N/A = not applicable". Within the command description tables, the
contend is normally given as '1'. Data fields labeled by N/A might be reserved for later variants of the
TMC222 and the content should be ignored for the TMC222.
Concerning response datagrams, the byte 0 is the slave address that is applied for addressing, where
the byte 1 is the slave address that is sent back within the response data frame.
6.8.1
GetFullStatus1
This command is provided to the circuit by the Master to get a complete status of the circuit and of the
stepper-motor. The parameters sent via the two wire serial bus to the Master are:
coil peak and hold current values (Irun and Ihold)
maximum and minimum velocities for the stepper-motor (Vmax and Vmin)
direction of motion clockwise / counterclockwise (Shaft)
stepping mode (StepMode) (Table 11: StepMode on page 21)
acceleration (deceleration) for the Stepper motor (Acc)
acceleration shape (AccShape)
status information:
motion status <Motion [2:0]>
over current flags for coil A <OVC1> and coil B <OVC2>
digital supply reset <VddReset>
charge pump status <CPFail>
external switch status <ESW>
step loss <StepLoss>
electrical defect <ElDef>
under voltage <UV2>
temperature information <Tinfo>
temperature warning <TW>
temperature shutdown <TSD>
GetFullStatus1 command
Byte
Content
Structure
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
Slave Address
1
OTP3
OTP2
OTP1
OTP0
HW
0
1
GetFullStatus1
1
0
1
GetFullStatus1 command (Response)
Byte
Content
Structure
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
Slave Address
1
OTP3
OTP2
OTP1
OTP0
HW
1
Address
1
OTP3
OTP2
OTP1
OTP0
HW
2
Irun & Ihold
Irun (3:0)
Ihold (3:0)
3
Vmax & Vmin
Vmax (3:0)
Vmin (3:0)
4
Status 1
AccShape
StepMode(1:0)
Shaft
ACC(3:0)
5
Status 2
VddReset
StepLoss
ElDef
UV2
TSD
TW
Tinfo(1:0)
6
Status 3
Motion(2:0)
ESW
OVC1
OVC2
1
CPFail
7
N/A
1
8
N/A
1
Note: N/A = not applicable
相關PDF資料 |
PDF描述 |
|---|---|
| TMC22290R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC22291R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC2301G8A1 | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301G8A | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301L1A1 | SPECIALTY CONSUMER CIRCUIT, CQCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC222-SI | 制造商:Trinamic 功能描述:MOTOR CNTRL I2C INTERFACE SOIC20 制造商:Trinamic 功能描述:MOTOR CNTRL, I2C INTERFACE, SOIC20 制造商:Trinamic 功能描述:IC MOTOR CTRL/DRVR, STEPPER, SOIC-20; Motor Type:Stepper; No. of Outputs:4; Output Current:800mA; Driver Case Style:SOIC; No. of Pins:20; Supply Voltage Min:8V; Supply Voltage Max:29V; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| TMC223-EVAL | 制造商:Trinamic 功能描述:EVAL MODULE FOR TMC223 |
| TMC223-LI | 制造商:Trinamic 功能描述: 制造商:Trinamic 功能描述:IC MOTOR CTRLR/DVR I2C 32QFN |
| TMC223-SI | 制造商:Trinamic 功能描述:Bulk |
| TMC2242 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。