- 您現在的位置：買賣IC網 > PDF目錄98265 > TMC222-PI20 STEPPER MOTOR CONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | TMC222-PI20 |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, PDSO20 |
| 封裝： | SOIC-20 |
| 文件頁數： | 26/48頁 |
| 文件大小： | 457K |
| 代理商： | TMC222-PI20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
32
TMC222 DATASHEET (V. 1.12 / March 7, 2011)
Copyright 2004-2011 TRINAMIC Motion Control GmbH & Co. KG
6.8.4
GotoSecurePosition
This command is provided by the Master to one or all the stepper-motors to move to the secure
position SecPos[10:0]. It can also be triggered at the end of a RunInit initialization phase. If
SecPos[10:0] equals 0x400 (the most negative decimal value of -1024) the secure position is disabled
and the GotoSecurePosition command is ignored.
GotoSecurePosition command
Byte
Content
Structure
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
Slave Address
1
OTP3
OTP2
OTP1
OTP0
HW
0
1
GotoSecurePosition 1
0
1
0
6.8.5
HardStop
This command is internally triggered when an electrical problem is detected in one or both coils,
leading to switch off the H-bridges. If this problem is detected while the motor is moving, the
<StepLoss> flag is raised allowing to warn the Master that steps may have been lost at the next
GetFullStatus1 command. A HardStop command can also be issued by the Master for some safety
reasons.
HardStop command
Byte
Content
Structure
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
Slave Address
1
OTP3
OTP2
OTP1
OTP0
HW
0
1
HardStop
1
0
1
0
1
6.8.6
ResetPosition
This command is provided to the circuit by the Master to reset ActPos and TagPos registers, in order
to allow for an initialization of the stepper-motor position.
Hint: This command is ignored during motion. It has no effect during motion. The Status Flags (section
5.2.2, page 20) named 'Motion Status' indicate if the motor is at rest (velocity=0).
ResetPosition command
Byte
Content
Structure
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
Slave Address
1
OTP3
OTP2
OTP1
OTP0
HW
0
1
ResetPosition
1
0
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| TMC22290R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC22291R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC2301G8A1 | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301G8A | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301L1A1 | SPECIALTY CONSUMER CIRCUIT, CQCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC222-SI | 制造商:Trinamic 功能描述:MOTOR CNTRL I2C INTERFACE SOIC20 制造商:Trinamic 功能描述:MOTOR CNTRL, I2C INTERFACE, SOIC20 制造商:Trinamic 功能描述:IC MOTOR CTRL/DRVR, STEPPER, SOIC-20; Motor Type:Stepper; No. of Outputs:4; Output Current:800mA; Driver Case Style:SOIC; No. of Pins:20; Supply Voltage Min:8V; Supply Voltage Max:29V; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| TMC223-EVAL | 制造商:Trinamic 功能描述:EVAL MODULE FOR TMC223 |
| TMC223-LI | 制造商:Trinamic 功能描述: 制造商:Trinamic 功能描述:IC MOTOR CTRLR/DVR I2C 32QFN |
| TMC223-SI | 制造商:Trinamic 功能描述:Bulk |
| TMC2242 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。