- 您現在的位置：買賣IC網 > PDF目錄98265 > TMC222-PI20 STEPPER MOTOR CONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | TMC222-PI20 |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, PDSO20 |
| 封裝： | SOIC-20 |
| 文件頁數： | 33/48頁 |
| 文件大?。?/td> | 457K |
| 代理商： | TMC222-PI20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
TMC222 DATASHEET (V. 1.12 / March 7, 2011)
39
Copyright 2004-2011 TRINAMIC Motion Control GmbH & Co. KG
7.3
Using the device
Q: What is the meaning of the ‘Shaft’ bit?
A: The Shaft bit determines the rotating direction of the motor, i.e. clockwise or counter-clockwise
rotation.
Q: How to generate an interrupt when the target position is reached?
A: This is not possible. The device hasn’t any interrupt output at all. Just poll ActPos or Motion[2:0]
using an appropriate command.
Q: How can I ensure that I always get consistent data for ActPos and ESW?
A: There isn’t a single command to read both ActPos and ESW simultaneously. GetFullStatus1 will
read ESW whereas GetFullStatus2 will read ActPos. Thus it is not possible to read consistent values
as long as a motion is in progress.
Q: How to specify a second target position to go to immediately after a first target position has
been reached?
A: This is possible using the RunInit command. Note, that after the second target position has been
reached the internal position counter ActPos is reset to zero.
Q: Is it possible to change Vmax on-the-fly?
A: Yes, it is, if the new velocity is in the same group as the old one (see Vmax Parameters). Otherwise
correct positioning is not ensured anymore. Vmax values are divided into four groups:
group A: Vmax index = 0
group B: Vmax index = 1, 2, 3, 4 ,5 or 6
group C: Vmax index = 7, 8, 9, 10 ,11 or 12
group D: Vmax index = 13, 14 or 15
Q: Is it possible to change the stepping mode on-the-fly?
A: Yes, it is possible and it has immediate effect on the current motion.
Q: How to operate in continuous velocity mode rather than positioning (ramp) mode?
A: There is no velocity mode. The device was designed primarily for positioning tasks so for each
motion there has to be specified a target position by the respective command. However, velocity mode
can be emulated by repeating the following two commands again and again:
Read ActPos using GetFullStatus2 command
Set lower 16 bits of [ActPos+32767] as the next target position using SetPosition command
For real continuous motion this sequence has to be repeated before the current target position has
been reached.
Q: Which units, formats and ranges does position information have?
A: All 16-bit position data fields in commands and responses are coded in two’s complement format
with bit 0 representing 1/16 micro-steps. Hence a position range of –32768…+32767 in units of 1/16
micro-steps is covered regardless of the selected stepping mode (1/2, 1/4, 1/8 or 1/16 micro-stepping).
The difference between the stepping modes is the resolution resp. the position of the LSB in the 16-bit
position data field: it’s bit 0 for 1/16, bit 1 for 1/8, bit 2 for 1/4 and bit 3 for 1/2 micro-stepping. The
position range can be regarded as a circle since position –32768 is just 1/16 micro-step away from
position +32767. The device will always take the shortest way from the current to the target position,
i.e., if the current position is +32767 and the target position is –32768 just 1/16 micro-step will be
executed. 65535 1/16 micro-steps in the opposite direction can be achieved for example by two
consecutive SetPosition commands with target positions 0 and –32768.
The 11-bit secure position data field can be treated as the upper 11 MSBs of the 16-bit position data
fields described above with the 5 LSBs hardwired to zero. Hence it covers the same position range with
a reduced resolution: The position range is –1024…+1023 in units of two full-steps.
相關PDF資料 |
PDF描述 |
|---|---|
| TMC22290R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC22291R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC2301G8A1 | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301G8A | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301L1A1 | SPECIALTY CONSUMER CIRCUIT, CQCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC222-SI | 制造商:Trinamic 功能描述:MOTOR CNTRL I2C INTERFACE SOIC20 制造商:Trinamic 功能描述:MOTOR CNTRL, I2C INTERFACE, SOIC20 制造商:Trinamic 功能描述:IC MOTOR CTRL/DRVR, STEPPER, SOIC-20; Motor Type:Stepper; No. of Outputs:4; Output Current:800mA; Driver Case Style:SOIC; No. of Pins:20; Supply Voltage Min:8V; Supply Voltage Max:29V; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| TMC223-EVAL | 制造商:Trinamic 功能描述:EVAL MODULE FOR TMC223 |
| TMC223-LI | 制造商:Trinamic 功能描述: 制造商:Trinamic 功能描述:IC MOTOR CTRLR/DVR I2C 32QFN |
| TMC223-SI | 制造商:Trinamic 功能描述:Bulk |
| TMC2242 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。