- 您現在的位置：買賣IC網 > PDF目錄98265 > TMC222-PI20 STEPPER MOTOR CONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | TMC222-PI20 |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, PDSO20 |
| 封裝： | SOIC-20 |
| 文件頁數： | 28/48頁 |
| 文件大小： | 457K |
| 代理商： | TMC222-PI20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
34
TMC222 DATASHEET (V. 1.12 / March 7, 2011)
Copyright 2004-2011 TRINAMIC Motion Control GmbH & Co. KG
6.8.9
SetMotorParam
This command is provided to the circuit by the Master to set the values for the following stepper motor
parameters in RAM:
coil peak current value (Irun)
coil hold current value (Ihold)
maximum velocity for the Stepper-motor (Vmax)
minimum velocity for the Stepper-motor (Vmin)
acceleration shape (AccShape)
stepping mode (StepMode)
direction of the Stepper-motor motion (Shaft)
acceleration (deceleration) for the Stepper-motor (Acc)
secure position for the Stepper-motor (SecPos)
If SecPos[10:0] is set to 0x400 (the most negative decimal value of –1024) the secure position is
disabled and the GotoSecurePosition command is ignored.
SetMotorParam command
Byte
Content
Structure
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
Slave Address
1
OTP3
OTP2
OTP1
OTP0
HW
0
1
SetMotorParam
1
0
1
0
1
2
N/A
1
3
N/A
1
4
Irun & I hold
Irun(3:0)
Ihold(3:0)
5
Vmax & Vmin
Vmax(3:0)
Vmin(3:0)
6
Status
SecPos(10:8)
Shaft
Acc(3:0)
7
SecurePos
SecPos(7:0)
8
StepMode
AccShape
StepMode[1:0]
Note: N/A = not applicable
6.8.10 SetOTPParam
This command is provided to the circuit by the Master in order to zap the OTP memory. The OTPA
address (OTPA) addresses the OTP word (please refer section 5.2.3, page 21) within the OTP
Memory structure. The Pbit byte represents the bit pattern to be programmed, where a one programs
an un-programmed OTP bit. For example, if one wants to OTP the defaults to Irun := 0xD and Ihold =
0x5, one has to execute the SetOTPParam with OTPA = 0x03 and Pbit := 0xD5. Those OTP bits that
are un-programmed can be programmed to '1' by corresponding Pbit chosen as '1' . For OTP the
supply voltage Vbat has to be within the valid range specified as VbbOTP within Table 21, page 45.
SetOTPParam command
Byte
Content
Structure
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
Slave Address
1
OTP3
OTP2
OTP1
OTP0
HW
0
1
SetOTPParam
1
0
1
0
2
N/A
1
3
N/A
1
4
OTP Address
1
OTPA(2:0)
5
Pbit
Pbit(7:0)
Note: N/A = not applicable
相關PDF資料 |
PDF描述 |
|---|---|
| TMC22290R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC22291R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC2301G8A1 | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301G8A | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301L1A1 | SPECIALTY CONSUMER CIRCUIT, CQCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC222-SI | 制造商:Trinamic 功能描述:MOTOR CNTRL I2C INTERFACE SOIC20 制造商:Trinamic 功能描述:MOTOR CNTRL, I2C INTERFACE, SOIC20 制造商:Trinamic 功能描述:IC MOTOR CTRL/DRVR, STEPPER, SOIC-20; Motor Type:Stepper; No. of Outputs:4; Output Current:800mA; Driver Case Style:SOIC; No. of Pins:20; Supply Voltage Min:8V; Supply Voltage Max:29V; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| TMC223-EVAL | 制造商:Trinamic 功能描述:EVAL MODULE FOR TMC223 |
| TMC223-LI | 制造商:Trinamic 功能描述: 制造商:Trinamic 功能描述:IC MOTOR CTRLR/DVR I2C 32QFN |
| TMC223-SI | 制造商:Trinamic 功能描述:Bulk |
| TMC2242 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。