- 您現在的位置：買賣IC網 > PDF目錄98265 > TMC222-PI20 STEPPER MOTOR CONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | TMC222-PI20 |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, PDSO20 |
| 封裝： | SOIC-20 |
| 文件頁數： | 27/48頁 |
| 文件大?。?/td> | 457K |
| 代理商： | TMC222-PI20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
TMC222 DATASHEET (V. 1.12 / March 7, 2011)
33
Copyright 2004-2011 TRINAMIC Motion Control GmbH & Co. KG
6.8.7
ResetToDefault
This command is provided to the circuit by the Master in order to reset the whole slave node into the
initial state. ResetToDefault will for instance overload the RAM with the reset state of the register
parameters. This is another way for the Master to initialize a slave node in case of emergency, or
simply to refresh the RAM content.
Note: ActPos is not modified by a ResetToDefault command, and it’s value is copied into TagPos
register in order to avoid an attempt to position the motor to ‘0’.
ResetToDefault command
Byte
Content
Structure
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
Slave Address
1
OTP3
OTP2
OTP1
OTP0
HW
0
1
ResetToDefault
1
0
1
6.8.8
RunInit
This command is provided to the circuit by the Master in order to initialize positioning of the motor by
seeking the zero (or reference) position. Refer to 5.1.11 Reference Search / Position initialization on
page 14. It leads to a sequence of the following commands:
SetMotorParam(Vmax, Vmin);
SetPosition(Pos1);
SetMotorParam(Vmin, Vmin);
SetPosition(Pos2);
ResetPosition
GotoSecurePosition
Once the RunInit command is started it can not be interrupted by any other command except when a
condition occurs which leads to a motor shutdown (See 5.1.10 Motor Shutdown Management) or a
HardStop command is received. If SecPos[10:0] equals 0x400 (the most negative decimal value of
-1024) the final travel to the secure position is omitted.
The master has to ensure that the target position of the first motion is not equal to the actual position
of the stepper motor and that the target positions of the first and second motion are different, too. This
is very important otherwise the circuit goes into a deadlock state. Once the circuit is in deadlock state
only a HardStop command followed by a GetFullStatus1 command will cause the circuit to leave the
deadlock state.
RunInit command
Byte
Content
Structure
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
Slave Address
1
OTP3
OTP2
OTP1
OTP0
HW
0
1
RunInit
1
0
1
0
2
N/A
1
3
N/A
1
4
Vmax Vmin
Vmax(3:0)
Vmin(3:0)
5
Position1 byte 1
TagPos1(15:8)
6
Position1 byte 2
TagPos1(7:0)
7
Position2 byte 1
TagPos2(15:8)
8
Position2 byte 2
TagPos2(7:0)
Note: N/A = not applicable
相關PDF資料 |
PDF描述 |
|---|---|
| TMC22290R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC22291R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC2301G8A1 | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301G8A | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301L1A1 | SPECIALTY CONSUMER CIRCUIT, CQCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC222-SI | 制造商:Trinamic 功能描述:MOTOR CNTRL I2C INTERFACE SOIC20 制造商:Trinamic 功能描述:MOTOR CNTRL, I2C INTERFACE, SOIC20 制造商:Trinamic 功能描述:IC MOTOR CTRL/DRVR, STEPPER, SOIC-20; Motor Type:Stepper; No. of Outputs:4; Output Current:800mA; Driver Case Style:SOIC; No. of Pins:20; Supply Voltage Min:8V; Supply Voltage Max:29V; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| TMC223-EVAL | 制造商:Trinamic 功能描述:EVAL MODULE FOR TMC223 |
| TMC223-LI | 制造商:Trinamic 功能描述: 制造商:Trinamic 功能描述:IC MOTOR CTRLR/DVR I2C 32QFN |
| TMC223-SI | 制造商:Trinamic 功能描述:Bulk |
| TMC2242 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。