- 您現在的位置：買賣IC網 > PDF目錄98281 > TPS40074RHLT (TEXAS INSTRUMENTS INC) 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 PDF資料下載
參數資料
| 型號： | TPS40074RHLT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | GREEN, PLASTIC, QFN-20 |
| 文件頁數： | 13/41頁 |
| 文件大小： | 765K |
| 代理商： | TPS40074RHLT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
www.ti.com
GROUNDING AND BOARD LAYOUT
SYNCHRONOUS RECTIFIER CONTROL
SLUS617B – APRIL 2005 – REVISED OCTOBER 2006
APPLICATION INFORMATION (continued)
The TPS40074 provides separate signal ground (GND) and power ground (PGND) pins. Care should be given
to proper separation of the circuit grounds. Each ground should consist of a plane to minimize its impedance if
possible. The high power noisy circuits such as the output, synchronous rectifier, MOSFET driver decoupling
capacitor (DBP), and the input capacitor should be connected to PGND plane.
Sensitive nodes such as the FB resistor divider and RT should be connected to the GND plane. The GND plane
should only make a single point connection to the PGND plane. It is suggested that the GND pin be tied to the
copper area for the PowerPAD underneath the chip. Tie the PGND to the PowerPAD copper area as well and
make the connection to the power circuit ground from the PGND pin. Reference the output voltage divider to the
GND pin.
Component placement should ensure that bypass capacitors (LVPB and DBP) are located as close as possible
to their respective power and ground pins. Also, sensitive circuits such as FB, RT and ILIM should not be
located near high dv/dt nodes such as HDRV, LDRV, BOOST, and the switch node (SW). Failure to follow
careful layout practices results in sub-optimal operation.
Table 2 describes the state of the rectifier MOSFET control under various operating conditions.
Table 2. Synchronous Rectifier MOSFET States
SYNCHRONOUS RECTIFIER OPERATION DURING
FAULT
SOFT-START
NORMAL
(FAULT RECOVERY IS SAME
OVERVOLTAGE
AS SOFT-START)
Off until first high-side pulse is
Turns off at the start of a new
Turns OFF only at start of next
detected, then on when high-side
cycle. Turns on when the
OFF
cycle ON if duty cycle is > 0
MOSFET is off
high-side MOSFET is turned off
For proper operation, the total gate charge of the MOSFET connected to LDRV should be less than 50nC.
20
相關PDF資料 |
PDF描述 |
|---|---|
| TPS40074RHLRG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40074RHL | 2 A SWITCHING CONTROLLER, 550 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40075RHLR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40075RHLTG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40077PWPR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS40074RHLTG4 | 功能描述:DC/DC 開關控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40075 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4.5V TO 18V INPUT 10 PIN SYNCHRONOUS BUCK CONTROLLER WITH POWER GOOD |
| TPS40075EVM-001 | 功能描述:電源管理IC開發工具 15A 12V In 1.5V Out Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS40075RHLR | 功能描述:DC/DC 開關控制器 Wide Input Synch Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40075RHLRG4 | 功能描述:DC/DC 開關控制器 Wide Input Synch Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。