- 您現在的位置：買賣IC網 > PDF目錄98281 > TPS40074RHLT (TEXAS INSTRUMENTS INC) 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 PDF資料下載
參數資料
| 型號： | TPS40074RHLT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | GREEN, PLASTIC, QFN-20 |
| 文件頁數： | 18/41頁 |
| 文件大小： | 765K |
| 代理商： | TPS40074RHLT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
www.ti.com
P
QSR + PQSR(CON) ) PDIODE ) PQSR(GATE)
(31)
P
QSR(CON) + RDS(on
1 *
V
O
V
IN
* t1 ) t2
f
SW
I
LOAD
2
) D
I2
12
(32)
P
DIODE + Vf
I
LOAD
t
1 ) t2
f
SW
(33)
P
QSR(GATE) + Qg(TOTAL)
Vg
f
SW
(34)
R
T +
1
f
SW
17.82
10*6
* 23
(35)
R
KFF + 0.131
R
T
V
UVLO(on) * 1.61
10*3
V
UVLO(on)
2
) 1.886
V
UVLO * 1.363 * 0.02
R
T * 4.87
10*5
R2
T
SLUS617B – APRIL 2005 – REVISED OCTOBER 2006
The calculations for the losses in the rectifier MOSFET are show in Equation 31 through Equation 34.
where
P
DIODE = body diode losses
t
1 = body diode conduction prior to turn on of channel = 10 ns for predictive gate drive
t
2 = body diode conduction after turn off of channel = 10 ns for predictive gate drive
V
f = body diode forward voltage
Estimating the body diode losses based on a forward voltage of 1.2 V gives 0.142 W. The gate losses are
unknown at this time so assume 0.1 W gate losses. This leaves 0.258 W for conduction losses. Using this figure
a target RDS(on) of 1.1 m was calculated. This is an extremely low value. It is not possible to meet this without
paralleling multiple MOSFETs. Paralleling MOSFETs increases the gate capacitance and slows down switching
speeds. This increases body diode and gate losses.
The PH2625L from Philips was chosen. Using the parameters from its data sheet the actual expected power
losses were calculated. Conduction loss is 0.527 W, body diode loss is 0.142 W and the gate loss was 0.174 W.
This totals 0.843 W associated with the rectifier MOSFET. This is somewhat greater than the initial allowance.
Because of this the converter may not hit its efficiency figure at the maximum load.
Two other criteria should be verified before finalizing on the rectifier MOSFET. One is the requirement to ensure
that predictive gate drive functions correctly. The maximum turn off delay of the PH2625L is 67 ns. The minimum
turn on delay of the PH6325L is 25 ns. These devices easily meet the 100 ns difference requirement.
Secondly the ratio between Cgs and Cgd should be greater than 1. The Cgs of the PH2625L is 2133 pF and the
Cgd is 1622 pF, so the Cgs:Cgd ratio is 1.3:1. This helps reduce the risk of dv/dt induced turn on of the rectifier
MOSFET. If this is likely to be a problem a small resistor may be added in series with the boost capacitor,
CBOOST.
3.2 Component Selection for TPS40074
3.2.1 Timing Resistor, RT
The timing resistor is calculated using the following equation.
This gives a resistor value of 117.3 k
. Using the E24 range of resistor values a 118-k resistor was selected.
The nominal frequency using this resistor is 398 kHz.
3.2.2 Feed Forward and UVLO Resistor, RKFF
A resistor connected to the KFF pin of the device feeds into the ramp generator. This resistor provides current
into the ramp generator proportional to the input voltage. The ramp is then adjusted to compensate for different
input voltages. Is provides the voltage feed forward feature of the TPS40074.
The same resistor also sets the under voltage lock out point. The input start voltage should be used to calculate
a value for RKFF. For this converter the minimum input voltage is 10.8 V however due to tolerances in the device,
a start voltage of 15% less than the minimum input voltage is selected. The start voltage for RKFF calculation is
(36)
where
25
相關PDF資料 |
PDF描述 |
|---|---|
| TPS40074RHLRG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40074RHL | 2 A SWITCHING CONTROLLER, 550 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40075RHLR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40075RHLTG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40077PWPR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS40074RHLTG4 | 功能描述:DC/DC 開關控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40075 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4.5V TO 18V INPUT 10 PIN SYNCHRONOUS BUCK CONTROLLER WITH POWER GOOD |
| TPS40075EVM-001 | 功能描述:電源管理IC開發工具 15A 12V In 1.5V Out Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS40075RHLR | 功能描述:DC/DC 開關控制器 Wide Input Synch Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40075RHLRG4 | 功能描述:DC/DC 開關控制器 Wide Input Synch Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。