欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： XBIB-U
廠商： Digi International/Maxstream
文件頁數： 35/72頁
文件大小： 1116K
描述： BOARD USB ZIGBEE MOD PRO
設計資源： XBIB-U Shematic
標準包裝： 1
附件類型： 接口板
適用于相關產品： XBee 和 XBee Pro 收音機
XBee/XBeePRO"燨EM燫F燤odules??02.15.4?爒1.xAx燵2007.05.031]
2007燤axStream,營nc.
牋牋?5
Chapter??燫F燤odule燙onfiguration
AC (Apply Changes) Command
<AT Command Mode Options> The AC command
is used to explicitly apply changes to module
parameter values. Applying changes means that
the module is re-initialized based on changes
made to its parameter values. Once changes are applied, the module immediately operates
according to the new parameter values.
This behavior is in contrast to issuing the WR (Write) command. The WR command saves parame-
ter values to non-volatile memory, but the module still operates according to previously saved val-
ues until the module is re-booted or the CN (Exit AT Command Mode) command is issued.
Refer to the AT Command - Queue Parameter Value API type for more information.
AI (Association Indication) Command
<Networking {Association}> The AI command is
used to indicate occurrences of errors during the
last association request.
Use the table below to determine meaning of the
returned values.
Returned Value (Hex)
Association Indication
0x00
Successful Completion - Coordinator successfully started or End Device association complete
0x01
Active Scan Timeout
0x02
Active Scan found no PANs
0x03
Active Scan found PAN, but the Coordinator Allow Association bit is not set
0x04
Active Scan found PAN, but Coordinator and End Device are not configured to support beacons
0x05
Active Scan found PAN, but Coordinator ID (PAN ID) value does not match the ID of the End Device
0x06
Active Scan found PAN, but Coordinator CH (Channel) value does not match the CH of the End Device
0x07
Energy Scan Timeout
0x08
Coordinator start request failed
0x09
Coordinator could not start due to Invalid Parameter
0x0A
Coordinator Realignment is in progress
0x0B
Association Request not sent
0x0C
Association Request timed out - no reply was received
0x0D
Association Request had an Invalid Parameter
0x0E
Association Request Channel Access Failure - Request was not transmitted - CCA failure
0x0F
Remote Coordinator did not send an ACK after Association Request was sent
0x10
Remote Coordinator did not reply to the Association Request, but an ACK was received
after sending the request
0x11
[reserved]
0x12
Sync-Loss - Lost synchronization with a Beaconing Coordinator
0x13
Disassociated - No longer associated to Coordinator
0xFF
RF Module is attempting to associate
AT Command: ATAC
Minimum Firmware Version Required: v1.xA0
AT Command: ATAI
Parameter Range: 0 - 0x13 [read-only]
Related Commands: AS (Active Scan), ID (PAN
ID), CH (Channel), ED (Energy Scan), A1 (End
Device Association), A2 (Coordinator
Association), CE (Coordinator Enable)
Minimum Firmware Version Required: v1.x80
相關PDF資料
PDF描述
XIB-E BOARD INTERFACE ETHERNET
XIB-R BOARD INTERFACE RS232/485
ZMN2400HPDB BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC IC TEMP SENSOR NI1000 SOT23-3
相關代理商/技術參數
參數描述
XBIB-U-DEV 功能描述:界面開發工具 USB XBee-PRO profes onal interface board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XBIB-U-SP 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Pads RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XBIB-U-SS 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Skt RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XBL6450BYFVR 制造商:Texas Instruments 功能描述:ECS BLUELINK - Tape and Reel
XBL6450YFHR 制造商:Texas Instruments 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 雷州市| 罗源县| 镇远县| 绵阳市| 深泽县| 怀来县| 恩平市| 长白| 米泉市| 西峡县| 新昌县| 密云县| 革吉县| 泗洪县| 阿图什市| 广安市| 姜堰市| 年辖：市辖区| 凤庆县| 成武县| 岳池县| 抚顺县| 福州市| 曲松县| 南皮县| 托克托县| 金坛市| 永安市| 吉林市| 巢湖市| 棋牌| 松江区| 凤山市| 永清县| 剑阁县| 高要市| 固镇县| 郴州市| 甘孜| 从化市| 门头沟区|