- 您現在的位置：買賣IC網 > Datasheet目錄58 > XBIB-U (Digi International/Maxstream)BOARD USB ZIGBEE MOD PRO Datasheet資料下載
參數資料
| 型號： | XBIB-U |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 53/72頁 |
| 文件大小： | 1116K |
| 描述： | BOARD USB ZIGBEE MOD PRO |
| 設計資源： | XBIB-U Shematic |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XBee 和 XBee Pro 收音機 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
XBee/XBeePRO"燨EM燫F燤odules??02.15.4?爒1.xAx燵2007.05.031]
2007燤axStream,營nc.
牋牋?3
Chapter??燫F燤odule燙onfiguration
T0 - T7 ((D0-D7) Output Timeout) Command
<I/O Settings {I/O Line Passing}> The T0, T1,
T2, T3, T4, T5, T6 and T7 commands are used to
set/read output timeout values for the lines that
correspond with the D0 - D7 parameters. When
output is set (due to I/O line passing) to a non-
default level, a timer is started which when
expired, will set the output to its default level. The timer is reset when a valid I/O packet is
received. The Tn parameter defines the permissible amount of time to stay in a non-default
(active) state. If Tn = 0, Output Timeout is disabled (output levels are held indefinitely).
VL (Firmware Version - Verbose)
<Diagnostics> The VL command is used to read
detailed version information about the RF module.
The information includes:
application build date; MAC, PHY and bootloader
versions; and build dates.
VR (Firmware Version) Command
<Diagnostics> The VR command is used to read
which firmware version is stored in the module.
XBee version numbers will have four significant
digits. The reported number will show three or
four numbers and is stated in hexadecimal notation. A version can be reported as "ABC" or
"ABCD". Digits ABC are the main release number and D is the revision number from the main
release. "D" is not required and if it is not present, a zero is assumed for D. "B" is a variant desig-
nator. The following variants exist:
" "0" = Non-Beacon Enabled 802.15.4 Code
" "1" = Beacon Enabled 802.15.4 Code
WR (Write) Command
<(Special)> The WR command is used to write
configurable parameters to the RF module's non-
volatile memory. Parameter values remain in the
module's memory until overwritten by subsequent use of the WR Command.
If changes are made without writing them to non-volatile memory, the module reverts back to pre-
viously saved parameters the next time the module is powered-on.
NOTE: Once the WR command is sent to the module, no additional characters should be sent until
after the OK/r response is received.
AT Commands: ATT0 - ATT7
Parameter Range:0 - 0xFF [x 100 msec]
Default Parameter Value:0xFF
Minimum Firmware Version Required: v1.xA0
AT Command: ATVL
Parameter Range:0 - 0xFF
[x 100 milliseconds]
Default Parameter Value: 0x28 (40 decimal)
Minimum Firmware Version Required: v1.x80
AT Command: ATVR
Parameter Range: 0 - 0xFFFF [read only]
AT Command: ATWR
相關PDF資料 |
PDF描述 |
|---|---|
| XIB-E | BOARD INTERFACE ETHERNET |
| XIB-R | BOARD INTERFACE RS232/485 |
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XBIB-U-DEV | 功能描述:界面開發工具 USB XBee-PRO profes onal interface board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XBIB-U-SP | 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Pads RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XBIB-U-SS | 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Skt RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XBL6450BYFVR | 制造商:Texas Instruments 功能描述:ECS BLUELINK - Tape and Reel |
| XBL6450YFHR | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。