- 您現在的位置：買賣IC網 > Datasheet目錄58 > XBIB-U (Digi International/Maxstream)BOARD USB ZIGBEE MOD PRO Datasheet資料下載
參數資料
| 型號： | XBIB-U |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 40/72頁 |
| 文件大小： | 1116K |
| 描述： | BOARD USB ZIGBEE MOD PRO |
| 設計資源： | XBIB-U Shematic |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XBee 和 XBee Pro 收音機 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
XBee/XBeePRO"燨EM燫F燤odules??02.15.4?爒1.xAx燵2007.05.031]
2007燤axStream,營nc.
牋牋?0
Chapter??燫F燤odule燙onfiguration
D7 (DIO7 Configuration) Command
<I/O Settings> The D7 command is used to
select/read the behavior of the DIO7 line (pin 12).
Options include:
" CTS flow control
" Analog-to-digital converter
" Digital input
" Digital output
D8 (DI8 Configuration) Command
<I/O Settings> The D8 command is used to
select/read the behavior of the DI8 line (pin 9).
This command enables configuring the pin to
function as a digital input. This line is also used
with Pin Sleep.
DA (Force Disassociation) Command
<(Special)> The DA command is used to immedi-
ately disassociate an End Device from a Coordi-
nator and reattempt to associate.
DB (Received Signal Strength) Command
<Diagnostics> DB parameter is used to read the
received signal strength (in dBm) of the last RF
packet received. Reported values are accurate
between -40 dBm and the RF module's receiver
sensitivity.
Absolute values are reported. For example: 0x58 = -88 dBm (decimal). If no packets have been
received (since last reset, power cycle or sleep event), 0 will be reported.
DH (Destination Address High) Command
<Networking {Addressing}> The DH command is
used to set and read the upper 32 bits of the RF
module's 64-bit destination address. When com-
bined with the DL (Destination Address Low)
parameter, it defines the destination address used
for transmission.
An module will only communicate with other
modules having the same channel (CH parame-
ter), PAN ID (ID parameter) and destination address
(DH + DL parameters).
To transmit using a 16-bit address, set the DH parameter to zero and the DL parameter less than
0xFFFF. 0x000000000000FFFF (DL concatenated to DH) is the broadcast address for the PAN.
Refer to the XBee/XBee-PRO Addressing section for more information.
AT Command: ATD7
Parameter Range:0 - 5
Parameter
Configuration
0
Disabled
1
CTS Flow Control
2
n/a
3
DI
4
DO low
5
DO high
Default Parameter Value:1
Parameters 3-5 supported as of firmware
version 1.x.A0
AT Command: ATD8
Parameter Range:0 - 5
(1, 2, 4 & 5 n/a)
Parameter
Configuration
0
Disabled
3
DI
Default Parameter Value:0
Minimum Firmware Version Required: 1.xA0
AT Command: ATDA
Minimum Firmware Version Required: v1.x80
AT Command: ATDB
Parameter Range [read-only]:
0x17-0x5C (XBee), 0x24-0x64 (XBee-PRO)
AT Command: ATDH
Parameter Range: 0 - 0xFFFFFFFF
Default Parameter Value: 0
Related Commands: DL (Destination Address
Low), CH (Channel), ID (PAN VID), MY (Source
Address)
相關PDF資料 |
PDF描述 |
|---|---|
| XIB-E | BOARD INTERFACE ETHERNET |
| XIB-R | BOARD INTERFACE RS232/485 |
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XBIB-U-DEV | 功能描述:界面開發工具 USB XBee-PRO profes onal interface board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XBIB-U-SP | 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Pads RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XBIB-U-SS | 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Skt RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XBL6450BYFVR | 制造商:Texas Instruments 功能描述:ECS BLUELINK - Tape and Reel |
| XBL6450YFHR | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。