- 您現在的位置：買賣IC網 > Datasheet目錄58 > XBIB-U (Digi International/Maxstream)BOARD USB ZIGBEE MOD PRO Datasheet資料下載
參數資料
| 型號： | XBIB-U |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 45/72頁 |
| 文件大小： | 1116K |
| 描述： | BOARD USB ZIGBEE MOD PRO |
| 設計資源： | XBIB-U Shematic |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XBee 和 XBee Pro 收音機 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
XBee/XBeePRO"燨EM燫F燤odules??02.15.4?爒1.xAx燵2007.05.031]
2007燤axStream,營nc.
牋牋?5
Chapter??燫F燤odule燙onfiguration
IU (I/O Output Enable) Command
<I/O Settings> The IU command is used to dis-
able/enable I/O UART output. When enabled (IU
= 1), received I/O line data packets are sent out
the UART. The data is sent using an API frame
regardless of the current AP parameter value.
KY (AES Encryption Key) Command
<Networking {Security}> The KY command is
used to set the 128-bit AES (Advanced Encryption
Standard) key for encrypting/decrypting data.
Once set, the key cannot be read out of the mod-
ule by any means.
The entire payload of the packet is encrypted
using the key and the CRC is computed across the
ciphertext. When encryption is enabled, each packet carries an additional 16 Bytes to convey the
random CBC Initialization Vector (IV) to the receiver(s). The KY value may be 0 or any 128-bit
value. Any other value, including entering KY by itself with no parameters, is invalid. All ATKY
entries (valid or not) are received with a returned 'OK'.
A module with the wrong key (or no key) will receive encrypted data, but the data driven out the
serial port will be meaningless. A module with a key and encryption enabled will receive data sent
from a module without a key and the correct unencrypted data output will be sent out the serial
port. Because CBC mode is utilized, repetitive data appears differently in different transmissions
due to the randomly-generated IV.
When queried, the system will return an OK message and the value of the key will not be
returned.
M0 (PWM0 Output Level) Command
<I/O Settings> The M0 command is used to set/
read the output level of the PWM0 line (pin 6).
Before setting the line as an output:
1. Enable PWM0 output (P0 = 2)
2. Apply settings (use CN or AC)
The PWM period is 64 祍ec and there are 0x03FF
(1023 decimal) steps within this period. When M0
= 0 (0% PWM), 0x01FF (50% PWM), 0x03FF
(100% PWM), etc.
M1 (PWM1 Output Level) Command
<I/O Settings> The M1 command is used to set/
read the output level of the PWM1 line (pin 7).
Before setting the line as an output:
1. Enable PWM1 output (P1 = 2)
2. Apply settings (use CN or AC)
AT Command: ATIU
Parameter Range:0 - 1
Parameter
Configuration
0
Disabled -
Received I/O line data
packets will NOT sent
out UART.
1
Enabled -
Received I/O line data
will be sent out UART
Default Parameter Value:1
Minimum Firmware Version Required: 1.xA0
AT Command: ATKY
Parameter Range:0 - (any 16-Byte value)
Default Parameter Value:0
Related Command: EE (Encryption Enable)
Minimum Firmware Version Required: v1.xA0
AT Command: ATM0
Parameter Range:0 - 0x03FF [steps]
Default Parameter Value:0
Related Commands: P0 (PWM0 Enable), AC
(Apply Changes), CN (Exit Command Mode)
Minimum Firmware Version Required: v1.xA0
AT Command: ATM1
Parameter Range:0 - 0x03FF
Default Parameter Value:0
Related Commands: P1 (PWM1 Enable), AC
(Apply Changes), CN (Exit Command Mode)
Minimum Firmware Version Required: v1.xA0
相關PDF資料 |
PDF描述 |
|---|---|
| XIB-E | BOARD INTERFACE ETHERNET |
| XIB-R | BOARD INTERFACE RS232/485 |
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XBIB-U-DEV | 功能描述:界面開發工具 USB XBee-PRO profes onal interface board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XBIB-U-SP | 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Pads RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XBIB-U-SS | 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Skt RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XBL6450BYFVR | 制造商:Texas Instruments 功能描述:ECS BLUELINK - Tape and Reel |
| XBL6450YFHR | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。