I" />

欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: XC2S200-6PQG208C
廠商: Xilinx Inc
文件頁數: 18/99頁
文件大小: 0K
描述: IC SPARTAN-II FPGA 200K 208-PQFP
標準包裝: 24
系列: Spartan®-II
LAB/CLB數: 1176
邏輯元件/單元數: 5292
RAM 位總計: 57344
輸入/輸出數: 140
門數: 200000
電源電壓: 2.375 V ~ 2.625 V
安裝類型: 表面貼裝
工作溫度: 0°C ~ 85°C
封裝/外殼: 208-BFQFP
供應商設備封裝: 208-PQFP(28x28)
產品目錄頁面: 599 (CN2011-ZH PDF)
其它名稱: 122-1317
Spartan-II FPGA Family: Functional Description
DS001-2 (v2.8) June 13, 2008
Module 2 of 4
Product Specification
25
R
If CCLK is slower than FCCNH, the FPGA will never assert
BUSY. In this case, the above handshake is unnecessary,
and data can simply be entered into the FPGA every CCLK
cycle.
A configuration packet does not have to be written in one
continuous stretch, rather it can be split into many write
sequences. Each sequence would involve assertion of CS.
In applications where multiple clock cycles may be required
to access the configuration data before each byte can be
loaded into the Slave Parallel interface, a new byte of data
may not be ready for each consecutive CCLK edge. In such
a case the CS signal may be de-asserted until the next byte
is valid on D0-D7. While CS is High, the Slave Parallel
interface does not expect any data and ignores all CCLK
transitions. However, to avoid aborting configuration,
WRITE must continue to be asserted while CS is asserted.
Abort
To abort configuration during a write sequence, de-assert
WRITE while holding CS Low. The abort operation is
initiated at the rising edge of CCLK, as shown in Figure 21,
page 26. The device will remain BUSY until the aborted
operation is complete. After aborting configuration, data is
assumed to be unaligned to word boundaries and the FPGA
requires a new synchronization word prior to accepting any
new packets.
Boundary-Scan Mode
In the boundary-scan mode, no nondedicated pins are
required, configuration being done entirely through the
IEEE 1149.1 Test Access Port.
Configuration through the TAP uses the special CFG_IN
instruction. This instruction allows data input on TDI to be
converted into data packets for the internal configuration
bus.
The following steps are required to configure the FPGA
through the boundary-scan port.
1.
Load the CFG_IN instruction into the boundary-scan
instruction register (IR)
2.
Enter the Shift-DR (SDR) state
3.
Shift a standard configuration bitstream into TDI
4.
Return to Run-Test-Idle (RTI)
5.
Load the JSTART instruction into IR
6.
Enter the SDR state
7.
Clock TCK through the sequence (the length is
programmable)
8.
Return to RTI
Configuration and readback via the TAP is always available.
The boundary-scan mode simply locks out the other modes.
The boundary-scan mode is selected by a <10x> on the
mode pins (M0, M1, M2).
Readback
The configuration data stored in the Spartan-II FPGA
configuration memory can be readback for verification.
Along with the configuration data it is possible to readback
the contents of all flip-flops/latches, LUT RAMs, and block
RAMs. This capability is used for real-time debugging.
For more detailed information see XAPP176, Spartan-II
FPGA Family Configuration and Readback.
Figure 19: Loading Configuration Data for the Slave
Parallel Mode
Yes
No
FPGA
Driving BUSY
High?
After INIT
Goes High
Load One
Configuration
Byte on Next
CCLK Rising Edge
To CRC Check
DS001_19_032300
No
End of
Configuration
Data File?
Yes
User Drives
WRITE and CS
Low
User Drives
WRITE and CS
High
相關PDF資料
PDF描述
RSM06DSUI CONN EDGECARD 12POS DIP .156 SLD
ACM28DTAT CONN EDGECARD 56POS R/A .156 SLD
ABC36DRXI-S734 CONN EDGECARD 72POS DIP .100 SLD
RCB66DHAN-S621 EDGECARD 132POS DIP R/A .050 SLD
RMM06DSUI CONN EDGECARD 12POS DIP .156 SLD
相關代理商/技術參數
參數描述
XC2S200-6PQG208I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
XC2S200-6TQ144C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
XC2S200-6TQ144I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
XC2S200-6TQG144C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
XC2S200-6TQG144I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
主站蜘蛛池模板: 凤冈县| 北京市| 英超| 虎林市| 婺源县| 韶关市| 昌平区| 武安市| 西峡县| 赤壁市| 义马市| 江津市| 大英县| 孟州市| 永嘉县| 阜阳市| 湛江市| 精河县| 胶州市| 永善县| 正蓝旗| 洛隆县| 浙江省| 莲花县| 绥宁县| 安顺市| 仲巴县| 甘洛县| 五峰| 讷河市| 安吉县| 京山县| 栖霞市| 祁东县| 泰宁县| 汽车| 周口市| 岱山县| 永清县| 泸西县| 高密市|