- 您現在的位置：買賣IC網 > PDF目錄373916 > AD7760BCP (ANALOG DEVICES INC) 2.5 MSPS, 20-Bit ADC PDF資料下載
參數資料
| 型號： | AD7760BCP |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 2.5 MSPS, 20-Bit ADC |
| 中文描述： | 1-CH 20-BIT DELTA-SIGMA ADC, PARALLEL ACCESS, QCC48 |
| 封裝： | LFCSP-48 |
| 文件頁數： | 16/22頁 |
| 文件大小： | 868K |
| 代理商： | AD7760BCP |
AD7760
Preliminary Technical Data
USING THE AD7760
The following is the recommended sequence for powering up
and using the AD7760.
Rev. PrN | Page 16 of 22
1.
Apply Power
2.
Start clock oscillator, applying MCLK
3.
Take RESET low for a minimum of 1 MCLK cycle
4.
Wait a minimum of 2 MCLK cycles after RESET has
been released.
5.
Write to Control Register 2 to power up the ADC and
the differential amplifiers as required. The correct
Clock Divider (CDIV[1:0]) ratio should be
programmed here also.
6.
Write to Control Register 1 to set up the Output Data
Rate.
7.
Take SYNC low for a minimum of 2 MCLK cycles.
Data can now be read from the part using the default filter,
offset, gain and over range threshold values. The
conversion data read will not be valid however until the
group delay of the filter has passed. When this has
occurred, the DVALID bit read with the data LSW will be
set indicating that the data is indeed valid.
The user can now download their own filter if required
(see Downloading a User-Defined Filter). Values for gain,
offset and over range threshold registers can be written or
read at this stage. An internal calibration sequence can also
be initiated at this point.
BIAS RESISTOR SELECTION
The AD7760 requires a resistor to be connected between the
R
BIAS
pin and AGND. The value for this resistor is dependant on
the reference voltage being applied to the device. The resistor
value should be selected to give a current of 25μA through the
resistor to ground. For a 2.5V reference voltage, the correct
resistor value is 100k
and for a 4.096V reference, 160k
.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7760BSV | 2.5 MSPS, 20-Bit ADC |
| AD7769 | LC2MOS Analog I/O Port |
| AD7769AN | LC2MOS Analog I/O Port |
| AD7769AP | LC2MOS Analog I/O Port |
| AD7769JN | LC2MOS Analog I/O Port |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7760BCPZ | 制造商:Analog Devices 功能描述:2.5MSPS 18/20 BIT SIGMA DELTA ADC - Bulk |
| AD7760BST | 制造商:Analog Devices 功能描述:2.5MSPS 18/20 BIT SIGMA DELTA ADC - Bulk |
| AD7760BSV | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.5 MSPS, 20-Bit ADC |
| AD7760BSVZ | 功能描述:IC ADC 24BIT 2.5MSPS 64TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7760BSVZ-REEL | 功能描述:IC ADC 24BIT 2.5MSPS 64TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。