- 您現在的位置：買賣IC網 > PDF目錄373969 > AD9864-EB (Analog Devices, Inc.) IF Digitizing Subsystem PDF資料下載
參數資料
| 型號： | AD9864-EB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | IF Digitizing Subsystem |
| 中文描述： | 中頻數字化子系統 |
| 文件頁數： | 40/44頁 |
| 文件大小： | 1984K |
| 代理商： | AD9864-EB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁
AD9864
Rev. 0 | Page 40 of 44
25
23
24
33
35
31
29
28
43
42
47
19
20
25
23
24
33
31
29
28
19
20
43
42
47
35
VCO
FS
DOUTA
CLKOUT
FREF
CLKP
CLKN
LOP
LON
IFIN
15
AD9864
MASTER
IOUTC
LOOP
FILTER
38
IOUTC
15
PE
PD
PC
LOP
LON
IFIN
FS
DOUTA
CLKOUT
SYNCB
TO
DSP
CLKP
CLKN
IOUTL
TO DSP
FROM
DSP
LOOP
FILTER
C
VAR
R
D
R
F
C
P
C
Z
0.1
μ
F
L
OSC
R
BIAS
C
OSC
TO OTHER
AD9864s
FROM
CRYSTAL
OSCILLATION
VDDC
TO OTHER
AD9864s
AD9864
SLAVE
FREF
0
PE
PC
PD
SYNCB
Figure 72. Example of Synchronizing Multiple AD9864s
Split Path Rx Architecture
A split path Rx architecture may be attractive for those applica-
tions whose instantaneous dynamic range requirements exceed
the capability of a single AD9864 device. To cope with these
higher dynamic range requirements, two AD9864s can be oper-
ated in parallel with their respective clip points offset by a fixed
amount. Adding a fixed amount of attenuation in front of the
AD9864 and/or programming the attenuation setting of its in-
ternal VGA can adjust the input-referred clip point. To save
power and simplify hardware, the LO and CLK circuits of the
device can also be shared. Connecting the SYNCB pins of the two
devices and pulsing this line low synchronizes the two devices.
An example of this concept for possible use in a GSM base sta-
tion is shown in Figure 73. The signal chain consists of a high
linearity RF front end and IF stage followed by two AD9864s
operating in parallel. The RF front end consists of a duplexer
and preselect filter to pass the GSM RF band of interest. A high
performance LNA isolates the duplexer from the preselect filter
while providing sufficient gain to minimize system NF. An RF
mixer is used to downconvert the entire GSM band to a suitable
IF, where much of the channel selectivity is accomplished. The
170.6 MHz IF is chosen to avoid any self-induced spurs from
the AD9864. The IF stage consists of two SAW filters isolated
by a 15 dB gain stage.
The cascaded SAW filter response must provide sufficient
blocker rejection in order for the receiver to meet its sensitivity
requirements under worst-case blocker conditions. A compos-
ite response having 27 dB, 60 dB, and 100 dB rejection at
frequency offsets of ±0.8 MHz, ±1.6 MHz, and ±6.5 MHz, r
spectively, provides enough blocker suppression to ensure tha
the AD9864 with the lower clip point will not be overd
any blocker. This configuration results in the best possible re
ceiver sensitivity under all blocking conditions.
e-
t
riven by
-
The output of the last SAW filters drives the two AD9864s via a
direct signal path and an attenuated signal path. The direct path
corresponds to the AD9864 having the lowest clip point and
provides the highest receiver sensitivity with a system noise
figure of 4.7 dB. The VGA of this device is set for maximum
attenuation, so its clip point is approximately –17 dBm. Since
conversion gain from the antenna to the AD9864 is 19 dB, the
digital output of this path will nominally be selected unless the
target signal’s power exceeds –36 dBm at the antenna. The
attenuated path corresponds to the AD9864 having the highest
input-referred clip point, and its digital output point of this
path is set to 7 dBm by inserting a 30 dB attenuator and setting
the AD9864’s VGA to the middle of its 12 dB range. This
setting results in a ±6 dB adjustment of the clip point, allowing
the clip point difference to be calibrated to exactly 24 dB, so
that a simple 5-bit shift would make up the gain difference. The
attenuated path can handle signal levels up to –12 dB at the
antenna before being overdriven. Since the SAW filters provide
sufficient blocker suppression, the digital data from this path
need only be selected when the target signal exceeds –36 dBm.
Although the sensitivity of the receiver with the attenuated path
is 20 dB lower than the direct path, the strong target signal
ensures a sufficiently high carrier-to-noise ratio.
Since GSM is based on a TDMA scheme, digital data (or path)
selection can occur on a slot-by-slot basis. The AD9864 would
be configured to provide Serial I and Q data at a frame rate of
541.67 kSPS, as well as additional information including a 2-bit
reset field and a 6-bit RSSI field. These two fields contain the
information needed to decide whether the direct or attenuated
path should be used for the current time slot.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9864BCPZ | IF Digitizing Subsystem |
| AD9864BCPZRL | IF Digitizing Subsystem |
| AD9866BCPRL | Broadband Modem Mixed Signal Front End |
| AD9866CHIPS | Broadband Modem Mixed Signal Front End |
| AD9866 | Broadband Modem Mixed Signal Front End |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9864-EBZ | 功能描述:BOARD EVAL FOR AD9864 制造商:analog devices inc. 系列:- 零件狀態:有效 類型:數字轉換器 頻率:10MHz ~ 300MHz 配套使用產品/相關產品:AD9864 所含物品:板 標準包裝:1 |
| AD9865 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Broadband Modem Mixed-Signal Front End |
| AD9865BCP | 制造商:Analog Devices 功能描述:Mixed Signal Front End 64-Pin LFCSP EP 制造商:Analog Devices 功能描述:MIXED SGNL FRONT END 64LFCSP EP - Trays 制造商:Analog Devices 功能描述:10BIT MIXED SIGNAL CONVERTER 9865 |
| AD9865BCPRL | 制造商:Analog Devices 功能描述:Mixed Signal Front End 64-Pin LFCSP EP T/R |
| AD9865BCPZ | 功能描述:IC PROCESSOR FRONT END 64LFCSP RoHS:是 類別:RF/IF 和 RFID >> RF 前端 (LNA + PA) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- RF 型:GPS 頻率:1575.42MHz 特點:- 封裝/外殼:48-TQFP 裸露焊盤 供應商設備封裝:48-TQFP 裸露焊盤（7x7） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。