- 您現在的位置：買賣IC網 > PDF目錄373969 > AD9864 (Analog Devices, Inc.) IF Digitizing Subsystem PDF資料下載
參數資料
| 型號： | AD9864 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | IF Digitizing Subsystem |
| 中文描述： | 中頻數字化子系統 |
| 文件頁數： | 17/44頁 |
| 文件大小： | 1984K |
| 代理商： | AD9864 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD9864
THEORY OF OPERATION
SERIAL PORT INTERFACE (SPI)
The serial port of the AD9864 has 3-wire or 4-wire SPI capabil-
ity, allowing read/write access to all registers that configure the
device’s internal parameters. The default 3-wire serial commu-
nication port consists of a clock (PC), peripheral enable (PE),
and bidirectional data (PD) signal. The inputs to PC, PE, and
PD contain a Schmitt trigger with a nominal hysteresis of 0.4 V
centered about the digital interface supply, i.e., VDDH/2.
A 4-wire SPI interface can be enabled by setting the MSB of the
SSICRB register (Reg. 0x19, Bit 7) and setting Reg. 0x3A to 00,
resulting in the output data appearing on the DOUTB pin.
Note that since the default power-up state sets DOUTB low,
bus contention is possible for systems sharing the SPI output
line. To avoid any bus contention, the DOUTB pin can be
three-stated by setting the fourth control bit in the three-state
bit (Reg. 0x3B, Bit 3). This bit can then be toggled to gain access
to the shared SPI output line. An 8-bit instruction header must
accompany each read and write SPI operation. Only the write
operation supports an auto-increment mode, which allows the
entire chip to be configured in a single write operation. The
instruction header is shown in Table 7. It includes a read/not-
write indicator bit, six address bits, and a Don’t Care bit. The
data bits immediately follow the instruction header for both
read and write operations. Note that the address and data are
always given MSB first.
Table 7. Instruction Header Information
MSB
I7
I6
I5
I4
R/W
A5
A4
A3
Rev. 0 | Page 17 of 44
I3
A2
I2
A1
I1
A0
LSB
I0
X
Figure 29 illustrates the timing requirements for a write opera-
tion to the SPI port. After the peripheral enable (PE) signal goes
low, data (PD) pertaining to the instruction header is read on
the rising edges of the clock (PC). To initiate a write operation,
the read/not-write bit is set low. After the instruction header is
read, the eight data bits pertaining to the specified register are
shifted into the data pin (PD) on the rising edges of the next
eight clock cycles. PE stays low during the operation and goes
high at the end of the transfer. If PE rises before the eight clock
cycles have passed, the operation is aborted. If PE stays low for
an additional eight clock cycles, the destination address is
incremented and another eight bits of data are shifted in.
Again, should PE rise early, the current byte is ignored. By
using this implicit addressing mode, the chip can be configured
with a single write operation. Registers identified as being sub-
ject to frequent updates, namely those associated with power
control and AGC operation, have been assigned adjacent
addresses to minimize the time required to update them. Note
that multibyte registers are big endian (the most significant
byte has the lower address) and are updated when a write to the
least significant byte occurs.
Figure 30 illustrates the timing for a read operation to the SPI
port. Although the AD9864 does not require read access for
proper operation, it is often useful in the product development
phase or for system authentication. Note that the read-back
enable bit (Register 0x3A, Bit 3) must be set for a read opera-
tion with a 3-wire SPI interface. After the peripheral enable
(PE) signal goes low, data (PD) pertaining to the instruction
header is read on the rising edges of the clock (PC). A read
operation occurs if the read/not-write indicator is set high.
After the address bits of the instruction header are read, the
eight data bits pertaining to the specified register are shifted out
of the data pin (PD) on the falling edges of the next eight clock
cycles. If the 4-wire SPI interface is enabled, the eight data bits
will also appear on the DOUTB pin with the same timing rela-
tionship as those appearing at PD. After the last data bit is
shifted out, the user should return PE high, causing PD to
become three-stated and return to its normal status as an input
pin. Since the auto-increment mode is not supported for read
operations, an instruction header is required for each register
read operation and PE must return high before initiating the
next read operation.
PE
PC
PD
t
H
t
DS
t
HI
t
S
t
DH
t
LOW
t
CLK
R/W
A5
A4
A0
D7
D6
D1
D0
DON'T
CARE
0
Figure 29.
SPI Write Operation Timing
相關PDF資料 |
PDF描述 |
|---|---|
| AD9864-EB | IF Digitizing Subsystem |
| AD9864BCPZ | IF Digitizing Subsystem |
| AD9864BCPZRL | IF Digitizing Subsystem |
| AD9866BCPRL | Broadband Modem Mixed Signal Front End |
| AD9866CHIPS | Broadband Modem Mixed Signal Front End |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9864BCP | 制造商:Analog Devices 功能描述:IF SUBSYS 48LFCSP EP - Bulk |
| AD9864BCPZ | 功能描述:IC IF SUBSYSTEM GEN-PURP 48LFCSP RoHS:是 類別:RF/IF 和 RFID >> RF 前端 (LNA + PA) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- RF 型:GPS 頻率:1575.42MHz 特點:- 封裝/外殼:48-TQFP 裸露焊盤 供應商設備封裝:48-TQFP 裸露焊盤（7x7） 包裝:托盤 |
| AD9864BCPZ | 制造商:Analog Devices 功能描述:IC, IF SUBSYSTEM, 16-24BIT, 6.8KHZ-270KH |
| AD9864BCPZRL | 功能描述:IC IF SUBSYSTEM GEN-PURP 48LFCSP RoHS:是 類別:RF/IF 和 RFID >> RF 前端 (LNA + PA) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- RF 型:GPS 頻率:1575.42MHz 特點:- 封裝/外殼:48-TQFP 裸露焊盤 供應商設備封裝:48-TQFP 裸露焊盤（7x7） 包裝:托盤 |
| AD9864-EB | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。