- 您現在的位置：買賣IC網 > PDF目錄374039 > ADUC824 (Analog Devices, Inc.) MicroConverter, Dual-Channel 16-/24-Bit ADCs with Embedded FLASH MCU PDF資料下載
參數資料
| 型號： | ADUC824 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 串行ADC |
| 英文描述： | MicroConverter, Dual-Channel 16-/24-Bit ADCs with Embedded FLASH MCU |
| 中文描述： | MicroConverter的，雙通道ADC的16-/24-Bit與嵌入式閃存MCU |
| 文件頁數： | 20/68頁 |
| 文件大小： | 1060K |
| 代理商： | ADUC824 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
REV. B
ADuC824
–20–
PIN FUNCTION DESCRIPTIONS (continued)
Pin
No.
Mnemonic
Type
*
Description
22–25
P3.4–P3.7
I/O
P3.4–P3.7 are bidirectional port pins with internal pull-up resistors. Port 3 pins that have 1s
written to them are pulled high by the internal pull-up resistors, and in that state can be used as
inputs. As inputs, Port 3 pins being pulled externally low will source current because of the
internal pull-up resistors. When driving a 0-to-1 output transition, a strong pull-up is active for
two core clock periods of the instruction cycle. The secondary functions of Port 3 pins are:
Timer/Counter 0 Input
Timer/Counter 1 Input
Write Control Signal, Logic Output. Latches the data byte from Port 0 into an external data memory.
Read Control Signal, Logic Output. Enables the data from an external data memory to Port 0.
Serial interface clock for either the I
2
C-compatible or SPI interface. As an input this pin is a Schmitt-
triggered input and a weak internal pull-up is present on this pin unless it is outputting logic low.
Serial data I/O for the I
2
C compatible interface or master output/slave input for the SPI interface.
A weak internal pull-up is present on this pin unless it is outputting logic low.
Port 2 is a bidirectional port with internal pull-up resistors. Port 2 pins that have 1s (A8–A11)
written to them are pulled high by the internal pull-up resistors, and in that state can (A16–A19)
be used as inputs. As inputs, Port 2 pins being pulled externally low will source current because
of the internal pull-up resistors. Port 2 emits the high order address bytes during fetches from
external program memory and middle and high order address bytes during accesses to the 24-bit
external data memory space.
Input to the crystal oscillator inverter
Output from the crystal oscillator inverter
Port 2 is a bidirectional port with internal pull-up resistors. Port 2 pins that have 1s (A12–A15)
written to them are pulled high by the internal pull-up resistors, and in that state they (A20–A23)
can be used as inputs. As inputs, Port 2 pins being pulled externally low will source current
because of the internal pull-up resistors. Port 2 emits the high order address bytes during fetches
from external program memory and middle and high order address bytes during accesses to the
24-bit external data memory space.
External Access Enable, Logic Input. When held high, this input enables the device to fetch
code from internal program memory locations 0000H to 1FFFH. When held low, this input
enables the device to fetch all instructions from external program memory. To determine the
mode of code execution, i.e., internal or external, the
EA
pin is sampled at the end of an external
RESET assertion or as part of a device power cycle.
EA
may also be used as an external emula-
tion I/O pin and therefore the voltage level at this pin must not be changed during normal mode
operation as it may cause an emulation interrupt that will halt code execution.
Program Store Enable, Logic Output. This output is a control signal that enables the external
program memory to the bus during external fetch operations. It is active every six oscillator
periods except during external data memory accesses. This pin remains high during internal
program execution.
PSEN
can also be used to enable serial download mode when pulled low
through a resistor at the end of an external RESET assertion or as part of a device power cycle.
Address Latch Enable, Logic Output. This output is used to latch the low byte (and page byte for
24-bit data address space accesses) of the address to external memory during external code or
data memory access cycles. It is activated every six oscillator periods except during an external
data memory access. It can be disabled by setting the PCON.4 bit in the PCON SFR.
P0.0 – P0.3 pins are part of Port 0, which is an 8-bit open-drain bidirectional.
I/O port. Port 0 pins that have 1s written to them float and in that state can be used as high impedance
inputs. An external pull-up resistor will be required on P0 outputsto force a valid logic high level
externally. Port 0 is also the multiplexed low-order address and data bus during accesses to external
program or data memory. In this application it uses strong internal pull-ups when emitting 1s.
P0.4 – P0.7 pins are part of Port 0, which is an 8-bit open drain bidirectional.
I/O port. Port 0 pins that have 1s written to them float and in that state can be used as high impedance
inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external
program or data memory. In this application it uses strong internal pull-ups when emitting 1s.
P3.4/T0
P3.5/T1
P3.6/
WR
P3.7/
RD
SCLK
I/O
I/O
I/O
I/O
I/O
26
27
SDATA/MOSI
I/O
28 – 31
P2.0 – P2.3
I/O
32
33
36 – 39
XTAL1
XTAL2
P2.4 – P2.7
I
O
I/O
40
EA
I/O
41
PSEN
O
42
ALE
O
43 – 46
P0.0 – P0.3
(AD0 – AD3)
I/O
49 – 52
P0.4 – P0.7
(AD4 – AD7)
I/O
*
I = Input, O = Output, S = Supply
NOTES
1. In the following descriptions, SET implies a Logic 1 state and CLEARED implies a Logic 0 state unless otherwise stated.
2. In the following descriptions, SET and CLEARED also imply that the bit is set or automatically cleared by the ADuC824 hardware unless otherwise stated.
3. User software should not write 1s to reserved or unimplemented bits as they may be used in future products.
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC824BS | MicroConverter, Dual-Channel 16-/24-Bit ADCs with Embedded FLASH MCU |
| ADUC831 | LJT 6C 6#22D PIN RECP |
| ADUC831BCP | Circular Connector; No. of Contacts:6; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:9; Circular Contact Gender:Socket; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:9-35 |
| ADUC831BS | MicroConverter, 12-Bit ADCs and DACs with Embedded 62 kBytes Flash MCU |
| ADUC836 | MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC824BCP | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 8KB FLASH 12.58MHZ 3.3/5V 56LFCSP - Bulk |
| ADUC824BCP-REEL | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP T/R |
| ADUC824BCPZ | 功能描述:IC MCU 8K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC824BS | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 8KB FLASH 12.58MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +24BIT ADC LQFP52 824 |
| ADUC824BS-DEN | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。