- 您現在的位置：買賣IC網 > PDF目錄374048 > ADV7393EBZ (Analog Devices, Inc.) Low Power, Chip Scale 10-Bit SD/HD Video Encoder PDF資料下載
參數資料
| 型號： | ADV7393EBZ |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Low Power, Chip Scale 10-Bit SD/HD Video Encoder |
| 中文描述： | 低功耗，芯片尺寸10位標清/高清視頻編碼器 |
| 文件頁數： | 51/96頁 |
| 文件大小： | 1209K |
| 代理商： | ADV7393EBZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
ADV7390/ADV7391/ADV7392/ADV7393
If RGB output is selected, the ED/HD CSC matrix scalar uses
the following equations:
R
=
GY
×
Y
+
RV
×
Pr
G
=
GY
×
Y
(
GU
×
Pb)
(
GV
×
Pr)
B
=
GY
×
Y
+
BU
×
Pb
Note that subtractions are implemented in hardware.
If YPrPb output is selected, the following equations are used:
Y
=
GY
×
Y
Pr
=
RV
×
Pr
Pb
=
BU
×
Pb
where:
GY
= Subaddress 0x05, Bits[7:0] and Subaddress 0x03, Bits[1:0].
GU
= Subaddress 0x06, Bits[7:0] and Subaddress 0x04, Bits[7:6].
GV
= Subaddress 0x07, Bits[7:0] and Subaddress 0x04, Bits[5:4].
BU
= Subaddress 0x08, Bits[7:0] and Subaddress 0x04, Bits[3:2].
RV
= Subaddress 0x09, Bits[7:0] and Subaddress 0x04, Bits[1:0].
Upon power-up, the CSC matrix is programmed with the
default values shown in Table 43.
Rev. 0 | Page 51 of 96
Table 43. ED/HD Manual CSC Matrix Default Values
Subaddress
0x03
0x04
0x05
0x06
0x07
0x08
0x09
When the ED/HD manual CSC matrix adjust feature is
enabled, the default coefficient values in Subaddress 0x03
to Subaddress 0x09 are correct for the HD color space only.
The color components are converted according to the following
1080i and 720p standards (SMPTE 274M, SMPTE 296M):
R
=
Y
+ 1.575
Pr
G
=
Y
0.468
Pr
0.187
Pb
B
=
Y
+ 1.855
Pb
The conversion coefficients should be multiplied by 315 before
being written to the ED/HD CSC matrix registers. This is
reflected in the default values for GY = 0x13B, GU = 0x03B,
GV = 0x093, BU = 0x248, and RV = 0x1F0.
If the ED/HD manual CSC matrix adjust feature is enabled and
another input standard (such as ED) is used, the scale values for
GY, GU, GV, BU, and RV must be adjusted according to this
input standard color space. The user should consider that the
color component conversion might use different scale values.
Default
0x03
0xF0
0x4E
0x0E
0x24
0x92
0x7C
For example, SMPTE 293M uses the following conversion:
R
=
Y
+ 1.402
Pr
G
=
Y
0.714
Pr
0.344
Pb
B
=
Y
+ 1.773
Pb
The programmable CSC matrix is used for external ED/HD
pixel data and is not functional when internal test patterns are
enabled.
Programming the CSC Matrix
If custom manipulation of the ED/HD CSC matrix coefficients
is required for a YCrCb-to-RGB color space conversion, follow
the following procedure:
1.
Enable the ED/HD manual CSC matrix adjust feature
(Subaddress 0x02, Bit 3).
2.
Set the output to RGB (Subaddress 0x02, Bit 5).
3.
Disable sync on PrPb (Subaddress 0x35, Bit 2).
4.
Enable sync on RGB (optional) (Subaddress 0x02, Bit 4).
The GY value controls the green signal output level, the BU
value controls the blue signal output level, and the RV value
controls the red signal output level.
SD LUMA AND COLOR CONTROL
Subaddress 0x9C to Subaddress 0x9F
SD Y Scale, SD Cb Scale, and SD Cr Scale are three 10-bit
control registers that scale the SD Y, Cb, and Cr output levels.
Each of these registers represent the value required to scale the
Cb or Cr level from 0.0 to 2.0 and the Y level from 0.0 to 1.5
times its initial level. The value of these 10 bits is calculated
using the following equation:
Y, Cb, or Cr Scale Value
=
Scale Factor
× 512
For example, if
Scale Factor
= 1.3
Y, Cb, or Cr Scale Value
= 1.3 × 512 = 665.6
Y, Cb, or Cr Scale Value
= 666
(rounded to the nearest integer)
Y, Cb, or Cr Scale Value
= 1010 0110 10b
Subaddress 0x9C, SD Scale LSB Register = 0x2A
Subaddress 0x9D, SD Y Scale Register = 0xA6
Subaddress 0x9E, SD Cb Scale Register = 0xA6
Subaddress 0x9F, SD Cr Scale Register = 0xA6
Note that this feature affects all interlaced output signals, that is,
CVBS, Y-C, YPrPb, and RGB.
相關PDF資料 |
PDF描述 |
|---|---|
| ADV7400AKSTZ-80 | 10-Bit Intergrated Multiformat SDTV/HDTV Video Decoder and RGB Graphics Digitizer |
| ADV7400AKSTZ-801 | 10-Bit Intergrated Multiformat SDTV/HDTV Video Decoder and RGB Graphics Digitizer |
| ADV7400ABSTZ-1101 | 10-Bit Intergrated Multiformat SDTV/HDTV Video Decoder and RGB Graphics Digitizer |
| ADV7400AKSTZ-110 | 10-Bit Intergrated Multiformat SDTV/HDTV Video Decoder and RGB Graphics Digitizer |
| ADV7400AKSTZ-1101 | 10-Bit Intergrated Multiformat SDTV/HDTV Video Decoder and RGB Graphics Digitizer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7393WBCPZ | 制造商:Analog Devices 功能描述:LOW POWER, CHIP SCALE 10-BIT SD/HD VIDEO ENCODER - Trays |
| ADV7393WBCPZ-REEL | 制造商:Analog Devices 功能描述:LOW POWER, CHIP SCALE 10-BIT SD/HD VIDEO ENCODER - Tape and Reel |
| ADV73946603 | 制造商:LG Corporation 功能描述:Frame Assembly |
| ADV73946604 | 制造商:LG Corporation 功能描述:Frame Assembly |
| ADV73946902 | 制造商:LG Corporation 功能描述:Frame Assembly |
發布緊急采購，3分鐘左右您將得到回復。