欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： SC418ULTRT
廠商： Semtech
文件頁數： 26/30頁
文件大小： 691K
描述： IC REG DL BUCK/LINEAR 20MLPQ
產品培訓模塊： Power Supplies 101
標準包裝： 1
系列： EcoSpeed®
拓撲： 降壓（降壓）（1），線性（LDO）（1）
功能： 任何功能
輸出數： 2
頻率 - 開關： 1MHz
電壓/電流 - 輸出 1： 控制器
電壓/電流 - 輸出 2： 0.75 V ~ 5.25 V，200mA
帶 LED 驅動器： 無
帶監控器： 無
帶序列發生器： 無
電源電壓： 3 V ~ 28 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 20-MLPQ
供應商設備封裝： 20-MLPQ（3x3）
包裝： 標準包裝
其它名稱： SC418ULTRTDKR
SC418
26
Applications Information (continued)
tor. For a conventional PWM constant-frequency con-
verter, as load increases the duty cycle also increases
slightly to compensate for IR and switching losses in the
MOSFETs and inductor. A adaptive on-time converter
must also compensate for the same losses by increasing
the effective duty cycle (more time is spent drawing
energy from V
IN
 as losses increase). Because the on-time is
essentially constant for a given V
OUT
/V
IN
 combination, to
offset the losses the off-time will reduce slightly as load
increases. The net effect is that switching frequency
increases slightly with increasing load.
PCB Layout Guidelines
As with any switch-mode converter, good PCB layout is
essential to achieving high performance. The following
guidelines will provide an optimum PCB layout.
The device layout can be considered in four parts.
Grounding for PGND and AGND
Power components
Low-noise analog circuits
Bypass capacitors
Grounding for PGND and AGND
A ground plane layer for PGND is recommended
to minimize the effects of switching noise, resis-
tive losses, and to maximize heat removal from
the power components.
A separate ground plane or island should be used
for AGND and all associated components. The
AGND island should avoid overlapping switching
signals on other layers (DH/DL/BST/LX).
Connect PGND and AGND together with a zero
ohm resistor or copper trace. Make the connec-
tion near the AGND and PGND pins of the IC.
Power Components
Use short, wide connections between the power
components.
Input capacitors and high-side MOSFETs
High-side and Low-side MOSFETs and inductor
(LX connection). Use wide copper traces to
provide high current carrying capacity and for
heat dissipation.
Inductor and output capacitors.
"
"
"
"
"
"
"
"
"
"
All PGND connections  the input capacitors,
low-side MOSFETs, output capacitors, and the
PGND pin of the SC48.
An inner layer ground plane is recom-
mended.
Each power component requires a short,
low impedance connection to the PGND
plane.
Place vias to the PGND plane directly near
the component pins.
Use short wide traces for the pin connections
from the SC48 (LX, DH, DL and BST). Do not
route these traces near the sensitive low-noise
analog signals (FB, FBL, TON, V
OUT
).
Low-noise Analog Circuits
Low-noise analog circuits are sensitive circuits that are
referenced to AGND. Due to their high impedance and
sensitivity to noise, it is important that these circuits be
kept away from the switching signals.
Use a plane or solid area for AGND. Place all
components connected to AGND above this
area.
Use short direct traces for the AGND con-
nections to all components.
Place vias to the AGND plane directly near
the component pins.
Proper routing of the V
OUT
 sense trace is essential
since it feeds into the FB resistor divider. Noise
on the FB waveform will cause instability and
multiple pulsing.
Connect the V
OUT
 sense trace directly to
the output capacitor or a ceramic bypass
capacitor.
Route this trace over to the VOUT pin,
carefully avoiding all switching signals
and power components.
Route this trace in a quiet layer if possible.
Route this trace away from the switch-
ing traces and components, even if the
trace is longer. Avoid shorter trace routing
through the power switching area.
If a bypass capacitor is used at the IC side
of the V
OUT
 sense trace, it should be placed
near the FB resistor divider.
"
?/DIV>
?/DIV>
?/DIV>
"
"
?/DIV>
?/DIV>
"
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
相關PDF資料
PDF描述
SC424MLTRT IC REG DL BUCK/LINEAR 28MLPQ
SC4250LISTRT IC HOT SWAP CTRLR 8-SOIC
SC427MLTRT IC REG DL BUCK/LINEAR 32MLPQ
SE95D,112 IC SENSOR TEMP 2.8-5.5V SOT96-1
SE97BTP,547 IC TEMP SENSOR DIMM 8HWSON
相關代理商/技術參數
參數描述
SC419 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:EcoSpeedTM DC-DC Converter with Integrated Boost Diode
SC419970CGCR2 制造商:Motorola Inc 功能描述:
SC419EVB 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:EcoSpeedTM DC-DC Converter with Integrated Boost Diode
SC419ULTRT 功能描述:IC REG CTRLR BUCK PWM 20-MLPQ RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:EcoSpeed®, SmartDrive™ 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR
SC41E6 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:SIEMENS ANNOUNCES A SUB-MICTON GENERATION OF CHANNELLESS GATE-ARRAYS BASED ON THE PROVEN MEGALOGIC PROCESS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 广宁县| 甘孜| 连平县| 磐安县| 彰化县| 涿鹿县| 汉寿县| 辉县市| 安顺市| 日照市| 龙门县| 遂川县| 伊川县| 双流县| 措美县| 中江县| 铁力市| 敦煌市| 竹溪县| 茶陵县| 汽车| 长治县| 岗巴县| 榆社县| 蚌埠市| 林周县| 故城县| 双辽市| 田阳县| 柳江县| 阿克苏市| 望谟县| 根河市| 菏泽市| 云龙县| 靖西县| 东方市| 娄底市| 连山| 游戏| 秦安县|