- 您現在的位置：買賣IC網 > PDF目錄68812 > 71M6543F-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543F-IGTR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 102/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543F-IGTR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁當前第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
v1.2
2008–2011 Teridian Semiconductor Corporation
49
FLSH_UNLOCK[3:0]. FLSH_UNLOCK[3:0] is not automatically reset. It should be cleared when the SPI or
ICE has finished changing the Flash. Table 41 summarizes the I/O RAM registers used for flash security.
Table 41: Flash Security
Name
Location
Rst
Wk
Dir
Description
FLSH_UNLOCK[3:0]
2702[7:4]
0
R/W
Must be a 2 to enable any flash modification.
See the description of Flash security for
more details.
SECURE
SFR B2[6]
0
R/W
Inhibits erasure of page 0 and flash addresses
above the beginning of CE code as defined
by CE_LCTN[6/5:0](I/O RAM 0x2109[5:0]) on
the 71M6543F/H and CE_LCTN[6:0] I/O
RAM 0x2109[6:0]) on the 71M6543G/GH.
Also inhibits the read of flash via the ICE
and SPI ports.
SPI Flash Mode
In normal operation, the SPI slave interface cannot read or write the flash memory. However, the
71M6543 contains a Special Flash Mode (SFM) that facilitates initial (production) programming of the
flash memory. When the 71M6543 is in SFM mode, the SPI interface can erase, read, and write the
flash. Other memory elements such as XRAM and I/O RAM are not accessible to the SPI in this mode.
In order to protect the flash contents, several operations are required before the SFM mode is successfully
invoked.
When the 71M6543G/GH is operating SFM, SPI single-byte transactions are used to write to
FL_BANK[1:0] (SFR 0xB6[1:0]). During an SPI single-byte transaction, SPI_CMD[1:0] will over-write the
contents of FL_BANK[1:0] (SFR 0xB6[1:0]). This will allow for access of the entire 128 KB flash memory
while operating in SFM.
Details on the SFM can be found in 2.5.12 SPI Slave Port.
2.5.1.2 MPU/CE RAM
The 71M6543 includes 5 KB of static RAM memory on-chip (XRAM) plus 256 bytes of internal RAM in the
MPU core. The 5KB of static RAM are used for data storage by both MPU and CE and for the
communication between MPU and CE.
2.5.1.3 I/O RAM (Configuration RAM)
The I/O RAM can be seen as a series of hardware registers that control basic hardware functions. I/O
RAM address space starts at 0x2000. The registers of the I/O RAM are listed in Table 69.
The 71M6543 includes 128 bytes non-volatile RAM memory on-chip in the I/O RAM address space
(addresses 0x2800 to 0x287F). This memory section is supported by the voltage applied at VBAT_RTC,
and the data in it are preserved in BRN, LCD, and SLP modes as long as the voltage at VBAT_RTC is
within specification.
2.5.2
Oscillator
The 71M6543 oscillator drives a standard 32.768 kHz watch crystal. This type of crystal is accurate and
does not require a high-current oscillator circuit. The oscillator has been designed specifically to handle
watch crystals and is compatible with their high impedance and limited power handling capability. The
oscillator power dissipation is very low to maximize the lifetime of any battery attached to VBAT_RTC.
Oscillator calibration can improve the accuracy of both the RTC and metering. Refer to 2.5.4, Real-Time
Clock (RTC) for more information.
The oscillator is powered from the V3P3SYS pin or from the VBAT_RTC pin, depending on the V3OK
internal bit (i.e., V3OK = 1 if V3P3SYS
≥ 2.8 VDC and V3OK = 0 if V3P3SYS < 2.8 VDC). The oscillator
requires approximately 100 nA, which is negligible compared to the internal leakage of a battery.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6543H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543FT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543FT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6543G | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543GH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:電表IC |
| 71M6543GHT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。