- 您現在的位置：買賣IC網 > PDF目錄68812 > 71M6543F-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543F-IGTR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 121/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543F-IGTR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁當前第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
66
2008–2011 Teridian Semiconductor Corporation
v1.2
For example, if LCD_MAP[46] = 1, then pin 93 (TMUX2OUT/SEG46) is configured as SEG46, and if
LCD_MAP[46]=0, then pin 93 is configured as TMUX2OUT.
The SEG pins with alternate ICE interface function (see pins 56-58 in Figure 43) are forced to their
alternate ICE interface function (i.e., E_RXTX, E_TCLK and E_RST) if the ICE_E pin (pin 59) is driven
high, and in this case, the bits LCD_MAP[50:48] (I/O RAM 0x2405[2:0]) bits are “don’t care” bits. If the
ICE_E pin is driven low, then LCD_MAP[50:48] bits must written with 1 in order to configure these pins as
SEG pins. If the ICE_E pin is low and LCD_MAP[50:48] are written with 0, then these pins are tied to an
internal pullup.
2.5.11 EEPROM Interface
The 71M6543 provides hardware support for either a two-pin or a three-wire (-wire) type of EEPROM
interface. The interfaces use the EECTRL (SFR 0x9F) and EEDATA (SFR 0x9E) registers for communication.
2.5.11.1 Two-pin EEPROM Interface
The dedicated 2-pin serial interface communicates with external EEPROM devices. The interface is
multiplexed onto the SEGDIO2 (SDCK) and SEGDIO3 (SDATA) pins and is selected by setting
DIO_EEX[1:0] = 01 (I/O RAM 0x2456[7:6]). The MPU communicates with the interface through the SFR
registers EEDATA and EECTRL. If the MPU wishes to write a byte of data to the EEPROM, it places the
data in EEDATA and then writes the Transmit code to EECTRL. This initiates the transmit operation which
is finished when the BUSY bit falls. INT5 is also asserted when BUSY falls. The MPU can then check the
RX_ACK bit to see if the EEPROM acknowledged the transmission.
A byte is read by writing the Receive command to EECTRL and waiting for the BUSY bit to fall. Upon
completion, the received data is in EEDATA. The serial transmit and receive clock is 78 kHz during each
transmission, and then holds in a high state until the next transmission. The EECTRL bits when the two-pin
interface is selected are shown in Table 55.
Table 55: EECTRL Bits for 2-pin Interface
Status
Bit
Name
Read/
Write
Reset
State
Polarity
Description
7
ERROR
R
0
Positive
1 when an illegal command is received.
6
BUSY
R
0
Positive
1 when serial data bus is busy.
5
RX_ACK
R
1
Positive
1 indicates that the EEPROM sent an ACK bit.
4
TX_ACK
R
1
Positive
1 indicates when an ACK bit has been sent to the
EEPROM.
3:0
CMD[3:0]
W
0000
Positive
CMD[3:0]
Operation
0000
No-op command. Stops the I
2C clock
(SDCK). If not issued, SDCK keeps
toggling.
0010
Receive a byte from the EEPROM and
send ACK.
0011
Transmit a byte to the EEPROM.
0101
Issue a STOP sequence.
0110
Receive the last byte from the
EEPROM and do not send ACK.
1001
Issue a START sequence.
Others
No operation, set the ERROR bit.
The EEPROM interface can also be operated by controlling the DIO2 and DIO3 pins directly. The
direction of the DIO line can be changed from input to output and an output value can be written
with a single write operation, thus avoiding collisions (see Table 14 Port Registers (SEGDIO0-15)).
Therefore, no resistor is required in series SDATA to protect against collisions.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6543H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543FT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543FT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6543G | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543GH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:電表IC |
| 71M6543GHT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。