- 您現在的位置：買賣IC網 > PDF目錄68812 > 71M6543F-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543F-IGTR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 128/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543F-IGTR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁當前第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
72
2008–2011 Teridian Semiconductor Corporation
v1.2
disabling the watchdog. SFMM and SFMS need to be written to in sequence in order to invoke SFM. This
sequential write process prevents inadvertent entering of SFM. The sequence for invoking SFM is:
First, write to SFMM (I/O RAM 0x2080) register. The value written to this register defines the SFM mode.
o
0xD1: Mass Erase mode. A Flash Mass erase cycle is invoked upon entering SFM.
o
0x2E: Flash Read back mode. SFM is entered for Flash read back purposes. Flash writes
will not be blocked and it is up to the user to guarantee that only previously unwritten
locations are written. This mode is not accessible when SPI secure mode is set.
o
SFM is not invoked if any other pattern is written to the SFMM register.
Next, write 0x96 to the SFMS (I/O RAM 0x2081) register. This write invokes SFM provided that the
previous write operation to SFMM met the requirements. Writing any other pattern to this register
does not invoke SFM. Additionally, any write operations to this register automatically reset the
previously written SFMM register values to zero.
SFM Details
The following occurs upon entering SFM.
The CE is disabled.
The MPU is halted. Once the MPU is halted it can only be restarted with a reset. This reset can be
accomplished with the RESET pin, a watchdog reset, or by cycling power (without battery at the
VBAT pin).
The Flash control logic is reset in case the MPU was in the middle of a Flash write operation or Erase
cycle.
Mass erase is invoked if specified in the SFMM (I/O RAM 0x2080) register (see Invoking SFM, above).
The SECURE bit (SFR 0xB2[6]) is cleared at the end of this and all Mass Erase cycles.
All SPI read and write operations now refer to Flash instead of XRAM space.
The SPI host can access the current state of the pending multi-cycle Flash access by performing a 4-byte
SPI write of any address and checking the status field.
All SPI write operations in SFM mode must be 6-byte write transactions that write two bytes to an even
address. The write transactions must contain a command byte of 0x00 which is the form that does not
create an MPU interrupt. Auto incrementing is disabled for write operations.
SPI read transactions can make use of auto increment and may access single bytes. The command byte
must always be 0x80 in SFM read transactions.
SPI commands in SFM
Interrupts are not generated in SFM since the MPU is halted. The format of the commands is shown in the
SPI Transactions description on Page 69.SPI Transactions
2.5.13 Hardware Watchdog Timer
An independent, robust, fixed-duration, watchdog timer (WDT) is included in the 71M6543. It uses the
RTC crystal oscillator as its time base and must be refreshed by the MPU firmware at least every
1.5 seconds. When not refreshed on time, the WDT overflows and the part is reset as if the RESET pin
were pulled high, except that the I/O RAM bits are in the same state as after a wake-up from SLP or LCD
modes (see the I/O RAM description in 5.2 for a list of I/O RAM bit states after RESET and wake-up).
Four thousand, one hundred CK32 cycles (or 125 ms) after the WDT overflow, the MPU is launched from
program address 0x0000.
The watchdog timer is also reset when the internal signal WAKE=0 (see 3.4 Wake-Up Behavior). The
WDT is disabled when the ICE_E pin is pulled high.
For details, see 3.3.4 Watchdog Timer (WDT) Reset.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6543H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543FT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543FT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6543G | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543GH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:電表IC |
| 71M6543GHT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。