- 您現在的位置：買賣IC網 > PDF目錄68812 > 71M6543F-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543F-IGTR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 119/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543F-IGTR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁當前第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
64
2008–2011 Teridian Semiconductor Corporation
v1.2
A small amount of power can be saved by programming the LCD frequency to the lowest value that
provides satisfactory LCD visibility over the required temperature range.
Table 53 shows all I/O RAM registers that control the operation of the LCD interface.
Table 53: LCD Configurations
Name
Location
Rst
Wk
Dir
Description
LCD_ALLCOM
2400[3]
0
–
R/W
Configures all 6 SEG/COM pins as COM. Has no effect
on pins whose LCD_MAP bit is zero.
LCD_BAT
2402[7]
0
–
R/W Connects the LCD power supply to VBAT in all modes.
LCD_E
2400[7]
0
–
R/W
Enables the LCD display. When disabled, VLC2,
VLC1, and VLC0 are ground as are the COM and SEG
outputs if their LCD_MAP bit is 1.
LCD_ON
LCD_BLANK
240C[0]
240C[1]
0
–
R/W
LCD_ON = 1 turns on all LCD segments without
affecting the LCD data. Similarly, LCD_BLANK = 1
turns off all LCD segments without affecting the LCD
data. If both bits are set, all LCD segments are turned
on.
LCD_RST
240C[2]
0
–
R/W
Clear all bits of LCD data. These bits affect SEGDIO
pins that are configured as LCD drivers.
LCD_DAC[4:0]
240D[4:0]
0
–
R/W
This register controls the LCD contrast DAC which
adjusts the VLCD voltage and has an output range of
2.65 VDC to 5.3 VDC. The VLCD voltage is
VLCD = 2.65 + 2.65 * LCD_DAC[4:0]/31
Thus, the LSB of the DAC is 85.5 mV. The maximum
DAC output voltage is limited by V3P3SYS, VBAT, and
whether LCD_BSTE is set.
LCD_CLK[1:0]
2400[1:0]
0
–
R/W
Sets the LCD clock frequency (1/T). See definition of T
in Figure 17.
Note: fw = 32768 Hz
00-fw/2^9, 01-fw/2^8, 10-fw/2^7, 11-fw/2^6
LCD_MODE[2:0]
2400[6:4]
0
–
R/W
The LCD bias and multiplex mode.
LCD_MODE
Output
000
4 states, 1/3 bias
001
3 states, 1/3 bias
010
2 states, bias
011
3 states, bias
100
Static display
101
5 states, 1/3 bias
110
6 states, 1/3 bias
LCD_VMODE[1:0]
2401[7:6]
00
R/W
This register specifies how VLCD is generated.
LCD_VMODE
Description
11
External VLCD
10
LCD boost and LCD DAC
enabled
01
LCD DAC enabled
00
No boost and no DAC.
VLCD = VBAT or V3P3SYS
The LCD can be driven in static, bias, and 1/3 bias modes. Figure 17 defines the COM waveforms.
Note that COM pins that are not required in a specific mode maintain a segment off state rather than
GND, VCC, or high impedance.
The segment drivers SEGDIO22 and SEGDIO23 can be configured to blink at either 0.5 Hz or 1 Hz.
The blink rate is controlled by LCD_Y (I/O RAM 0x2400[2]). There can be up to six pixels/segments
connected to each of these driver pins. The I/O RAM fields LCD_BLKMAP22[5:0] (I/O RAM 0x2402[5:0])
and LCD_BLKMAP23[5:0] (I/O RAM 0x2401[5:0]) identify which pixels, if any, are to blink.
LCD_BLKMAP22[5:0] and LCD_BLKMAP23[5:0] are non-volatile.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6543H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543FT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543FT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6543G | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543GH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:電表IC |
| 71M6543GHT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。