- 您現在的位置：買賣IC網 > PDF目錄68812 > 71M6543F-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543F-IGTR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 137/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543F-IGTR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁當前第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
80
2008–2011 Teridian Semiconductor Corporation
v1.2
3.3
Fault and Reset Behavior
3.3.1
Events at Power-Down
Power fault detection is performed by internal comparators that monitor the voltage at the V3P3A pin and
also monitor the internally generated VDD pin voltage (2.5 VDC). The V3P3SYS and V3P3A pins must be
tied together at the PCB level, so that the comparators, which are internally connected only to the V3P3A
pin, are able to simultaneously monitor the common V3P3SYS and V3P3A pin voltage. The following
discussion assumes that the V3P3A and V3P3SYS pins are tied together at the PCB level.
During a power failure, as V3P3A falls, two thresholds are detected:
The first threshold, at 3.0 VDC (VSTAT[2:0] = 001, SFR 0xF9[2:0]), warns the MPU that the analog
modules are no longer accurate. Other than warning the MPU, the hardware takes no action when
this threshold is crossed. This comparison produces an internal bit named V3OKA.
The second threshold, at 2.8 VDC, causes the 71M6543 to switch to battery power. This switching
happens while the FLASH and RAM systems are still able to read and write. This comparison
produces an internal bit named V3OK.
The power quality is reflected by the VSTAT[2:0] register in I/O RAM space, as shown in Table 63. The
VSTAT[2:0] register is located at SFR address F9 and occupies bits 2:0. The VSTAT[2:0] field can only be
read.
In addition to the state of the main power, the VSTAT[2:0] register provides information about the internal
VDD voltage under battery power. Note that if system power (V3P3A) is above 2.8 VDC, the 71M6543
always switches from battery to system power.
Table 63: VSTAT[2:0] (SFR 0xF9[2:0])
VSTAT[2:0]
Description
000
System Power OK. V3P3A > 3.0 VDC. Analog modules are functional and accurate.
001
System Power is low. 2.8 VDC < V3P3A < 3.0 VDC. Analog modules not accurate.
Switch over to battery power is imminent.
010
The IC is on battery power and VDD is OK. VDD > 2.25 VDC. The IC has full digital
functionality.
011
The IC is on battery power and 2.25 VDC > VDD > 2.0 VDC. Flash write operations are
inhibited.
101
The IC is on battery power and VDD < 2.0, which means that the MPU is nearly out of
voltage. A reset occurs in 4 cycles of the crystal clock CK32.
The response to a system power fault is almost entirely controlled by firmware. During a power failure,
system power slowly falls. This fall in power is monitored by internal comparators that cause the
hardware to automatically switch over to taking power from the VBAT input. An interrupt notifies the MPU
that the part is now battery powered. At this point, it is the MPU’s responsibility to reduce power by
slowing the clock rate, disabling the PLL, etc.
Precision analog components such as the bandgap reference, the bandgap buffer, and the ADC are
powered only by the V3P3A pin and become inaccurate and ultimately unavailable as the V3P3A pin
voltage continues to drop (i.e., circuits powered by the V3P3A pin are not backed by the VBAT pin).
When the V3P3A pin falls below 2.8 VDC, the ADC clocks are halted and the amplifiers are unbiased.
Meanwhile, control bits such as ADC_E bit (I/O RAM 0x2704[4]) are not affected, since their I/O RAM
storage is powered from the VDD pin (2.5 VDC). The VDD pin is supplied with power through an internal
2.5 VDC regulator that is connected to the V3P3D pin. In turn, the V3P3D pin is switched to receive
power from the VBAT pin when the V3P3SYS pin drops below 3.0 VDC. Note that the V3P3SYS and
V3P3A pins are typically tied together at the PCB level.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6543H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543FT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543FT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6543G | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543GH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:電表IC |
| 71M6543GHT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。