- 您現在的位置：買賣IC網 > PDF目錄373914 > AD7707 (Analog Devices, Inc.) ECONOLINE: REC2.2-S_DR/H1 - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- UL94V-0 Package Material- Continuous Short Circiut Protection- Internal SMD design- 100% Burned In- Efficiency to 75% PDF資料下載
參數資料
| 型號： | AD7707 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | ECONOLINE: REC2.2-S_DR/H1 - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- UL94V-0 Package Material- Continuous Short Circiut Protection- Internal SMD design- 100% Burned In- Efficiency to 75% |
| 中文描述： | 3 V / 5號第五，1毫瓦3 -10 V輸入范圍通道16位Σ-Δ模數轉換器 |
| 文件頁數： | 4/40頁 |
| 文件大小： | 316K |
| 代理商： | AD7707 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
REV. A
–4–
AD7707–SPECIFICATIONS
Parameter
B Version
1
Units
Conditions/Comments
POWER REQUIREMENTS (Continued)
DV
DD
Current
17
Digital I/Ps = 0V or DV
DD
. External MCLK IN
Typically 0.06mA. DV
DD
= 3V. f
CLK
IN
= 1MHz
Typically 0.13 mA. DV
DD
= 5V. f
CLK
IN
= 1MHz
Typically 0.15mA. DV
DD
= 3V. f
CLK
IN
= 2.4576MHz
Typically 0.3mA. DV
DD
= 5V. f
CLK
IN
= 2.4576MHz
0.080
0.15
0.18
0.35
See Note 20
mA max
mA max
mA max
mA max
dB typ
Power Supply Rejection
19
Normal Mode Power Dissipation
17
AV
DD
= DV
DD
= +3 V. Digital I/Ps = 0 V or DV
DD
.
External MCLK IN Excluding Dissipation in the AIN3
Attenuator
Typically 0.84 mW. BUF = 0. f
CLK
IN
= 1MHz, All Gains.
Typically 1.53 mW. BUF = 1. f
CLK
IN
= 1MHz, All Gains.
Typically 1.11 mW. BUF = 0. f
CLK
IN
= 2.4576 MHz,
Gain = 1 to 4.
Typically 1.9 mW. BUF = 1. f
CLK
IN
= 2.4576 MHz,
Gain = 1 to 4.
AV
DD
= DV
DD
= +5 V. Digital I/Ps = 0V or DV
DD
.
External MCLKIN
Typically 1.75 mW. BUF = 0. f
CLK
IN
= 1MHz, All Gains.
Typically 2.9 mW. BUF = 1. f
CLK
IN
= 1MHz, All Gains.
Typically 2.6 mW. BUF = 0. f
CLK
IN
= 2.4576 MHz.
Typically 3.75 mW. BUF = 1. f
IN
= 2.4576 MHz.
External MCLK IN = 0 V or DV
DD
. Typically 9
μ
A.
AV
DD
= +5 V
External MCLK IN = 0 V or DV
DD
. Typically 4
μ
A.
AV
DD
= +3 V
1.05
2.04
1.35
mW max
mW max
mW max
2.34
mW max
Normal Mode Power Dissipation
17
2.1
3.75
3.1
4.75
18
mW max
mW max
mW max
mW max
μ
A max
Standby (Power-Down) Current
18
8
μ
A max
NOTES
Temperature range as follows: B Version, –40
°
C to +85
°
C.
2
These numbers are established from characterization or design at initial product release.
3
A calibration is effectively a conversion so these errors will be of the order of the conversion noise shown in Tables I and III for the low level input channels AIN1
and AIN2. This applies after calibration at the temperature of interest.
4
Recalibration at any temperature will remove these drift errors.
5
Positive full-scale error includes zero-scale errors (unipolar offset error or bipolar zero error) and applies to both unipolar and bipolar input ranges.
6
Full-scale drift includes zero-scale drift (unipolar offset drift or bipolar zero drift) and applies to both unipolar and bipolar input ranges.
7
Gain error does not include zero-scale errors. It is calculated as full-scale error–unipolar offset error for unipolar ranges and full-scale error–bipolar zero error for
bipolar ranges.
8
Gain error drift does not include unipolar offset drift/bipolar zero drift. It is effectively the drift of the part if zero scale calibrations only were performed.
9
Error is removed following a system calibration.
10
This common-mode voltage range is allowed provided that the input voltage on analog inputs does not go more positive than AV
+ 30 mV or go more negative
than AGND – 100mV. Parts are functional with voltages down to AGND – 200 mV, but with increased leakage at high temperature.
11
The analog input voltage range on AIN(+) is given here with respect to the voltage on LCOM on the low level input channels (AIN1 and AIN2) and is given with
respect to the HCOM input on the high level input channel AIN3. The absolute voltage on the low level analog inputs should not go more positive than AV
+
100mV, or go more negative than GND– 100mV for specified performance. Input voltages of AGND – 200 mV can be accommodated, but with increased leakage
at high temperature.
12
V
= REF IN(+) – REF IN(–).
13
These logic output levels apply to the MCLK OUT only when it is loaded with one CMOS load.
14
Sample tested at +25
°
C to ensure compliance.
15
After calibration, if the analog input exceeds positive full scale, the converter will output all 1s. If the analog input is less than negative full scale, the device will
output all 0s.
16
These calibration and span limits apply provided the absolute voltage on the analog inputs does not exceed AV
DD
+ 30mV or go more negative than AGND –
30mV. The offset calibration limit applies to both the unipolar zero point and the bipolar zero point.
17
When using a crystal or ceramic resonator across the MCLK pins as the clock source for the device, the DV
DD
current and power dissipation will vary depending on
the crystal or resonator type (see Clocking and Oscillator Circuit section).
18
If the external master clock continues to run in standby mode, the standby current increases to 150
μ
A typical at 5 V and 75
μ
A at 3 V. When using a crystal or
ceramic resonator across the MCLK pins as the clock source for the device, the internal oscillator continues to run in standby mode and the power dissipation
depends on the crystal or resonator type (see Standby Mode section).
19
Measured at dc and applies in the selected passband. PSRR at 50Hz will exceed 120dB with filter notches of 25 Hz or 50Hz. PSRR at 60Hz will exceed 120dB
with filter notches of 20 Hz or 60Hz.
20
PSRR depends on both gain and AV
DD
.
Low Level Input Channels, AIN1 and AIN2
High Level Input Channel, AIN3
Gain
AV
DD
= 3 V
AV
DD
= 5 V
1
86
90
2
78
78
4
85
84
8–128
93
91
Gain
AV
DD
= 3 V
AV
DD
= 5 V
1
68
72
2
60
60
4
67
66
8–128
75
73
Specifications subject to change without notice.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7707EB | 3 V/5 V 610 V Input Range 1 mW 3-Channel 16-Bit Sigma-Delta ADC(316.51 k) |
| AD7708BR | Shaft; Style: 2 - light; Applicable Model: LE-P / LEL-W |
| AD7708BRU | 8-/10-Channel, Low Voltage, Low Power, ADCs |
| AD7708 | 8-/10-Channel, Low Voltage, Low Power, ADCs |
| AD7718 | 8-/10-Channel, Low Voltage, Low Power, ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7707BR | 功能描述:IC ADC 16BIT 3CH 20-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7707BR-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 500sps 16-bit Serial 20-Pin SOIC W T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.5KSPS 16BIT SERL 20SOIC W - Tape and Reel |
| AD7707BR-REEL7 | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 500sps 16-bit Serial 20-Pin SOIC W T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.5KSPS 16BIT SERL 20SOIC W - Tape and Reel |
| AD7707BRU | 功能描述:IC ADC 16BIT 3CH 20-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7707BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 500sps 16-bit Serial 20-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.5KSPS 16BIT SERL 20TSSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。