- 您現在的位置：買賣IC網 > PDF目錄373970 > AD9886KS-100 (ANALOG DEVICES INC) Analog Interface for Flat Panel Displays PDF資料下載
參數資料
| 型號： | AD9886KS-100 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | Analog Interface for Flat Panel Displays |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| 封裝： | PLASTIC, MQFP-160 |
| 文件頁數： | 11/32頁 |
| 文件大小： | 248K |
| 代理商： | AD9886KS-100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
REV. 0
AD9886
–11–
The clamp timing can be established by simply exercising the
CLAMP pin at the appropriate time (with EXTCLMP = 1).
The polarity of this signal is set by the Clamp Polarity bit.
A simpler method of clamp timing employs the AD9886 inter-
nal clamp timing generator. The Clamp Placement register is
programmed with the number of pixel times that should pass
after the trailing edge of HSYNC before clamping starts. A
second register (Clamp Duration) sets the duration of the
clamp. These are both 8-bit values, providing considerable
flexibility in clamp generation. The clamp timing is referenced
to the trailing edge of HSYNC because, although HSYNC
duration can vary widely, the back porch (black reference)
always follows HSYNC. A good starting point for establishing
clamping is to set the clamp placement to 08h (providing eight
pixel periods for the graphics signal to stabilize after sync) and
set the clamp duration to 14h (giving the clamp 20 pixel periods
to reestablish the black reference).
Clamping is accomplished by placing an appropriate charge on
the external input coupling capacitor. The value of this capaci-
tor affects the performance of the clamp. If it is too small, there
will be a significant amplitude change during a horizontal line
time (between clamping intervals). If the capacitor is too large,
it will take excessively long for the clamp to recover from a large
change in incoming signal offset. The recommended value
(47 nF) results in recovering from a step error of 100 mV to
within 1/2 LSB in 10 lines with a clamp duration of 20 pixel
periods on a 60 Hz SXGA signal.
YUV Clamping
YUV graphic signals are slightly different from RGB signals in
that the dc reference level (black level in RGB signals) can be at
the midpoint of the video signal rather than the bottom. For
these signals it can be necessary to clamp to the midscale range
of the A/D converter range (10h) rather than bottom of the A/D
converter range (00h).
Clamping to midscale rather than ground can be accomplished
by setting the clamp select bits in the series bus register. Each of
the three converters has its own selection bit so that they can be
clamped to either midscale or ground independently. These bits
are located in Register 0Fh and are Bits 0–2.
The midscale reference voltage that each A/D converter clamps
to is provided independently on the R
MIDSC
V, G
MIDSC
V, and
B
MIDSC
V pins. Each converter must have its own midscale refer-
ence because both offset adjustment and gain adjustment for
each converter will affect the dc level of midscale.
During clamping, each A/D converter is clamped to its respec-
tive midscale reference input. These inputs are pins R
CLAMP
V,
G
CLAMP
V, and B
CLAMP
V for the red, green, and blue converters
respectively. The typical connections for both RGB and YUV
clamping are shown below in Figure 2. Note: if midscale clamp-
ing is not required, all of the midscale voltage outputs should
still be connected to ground through a 0.1
μ
F capacitor.
R
MIDSC
V
R
CLAMP
V
G
MIDSC
V
G
CLAMP
V
B
MIDSC
V
B
CLAMP
V
0.1 F
0.1 F
0.1 F
Figure 2. Typical Clamp Configuration for RBG/YUV
Applications
Gain and Offset Control
The AD9886 can accommodate input signals with inputs rang-
ing from 0.5 V to 1.0 V full scale. The full-scale range is set in
three 8-bit registers (Red Gain, Green Gain, and Blue Gain).
Note that increasing the gain setting results in an image with
less contrast.
The offset control shifts the entire input range, resulting in a
change in image brightness. Three 7-bit registers (Red Offset,
Green Offset, Blue Offset) provide independent settings for
each channel.
The offset controls provide a
±
63 LSB adjustment range. This
range is connected with the full-scale range, so if the input range
is doubled (from 0.5 V to 1.0 V) then the offset step size is also
doubled (from 2 mV per step to 4 mV per step).
Figure 3 illustrates the interaction of gain and offset controls.
The magnitude of an LSB in offset adjustment is proportional
to the full-scale range, so changing the full-scale range also
changes the offset. The change is minimal if the offset setting is
near midscale. When changing the offset, the full-scale
range
is
not affected, but the full-scale
level
is shifted by the same amount
as the zero-scale level.
GAIN
1.0V
0.0V
00h
FFh
I
0.5V
OFFSET = 00h
OFFSET = 3Fh
OFFSET = 7Fh
OFFSET = 00h
OFFSET = 7Fh
OFFSET = 3Fh
Figure 3. Gain and Offset Control
相關PDF資料 |
PDF描述 |
|---|---|
| AD9886KS-140 | Analog Interface for Flat Panel Displays |
| AD9898 | CCD Signal Processor with Precision Timing⑩ Generator |
| AD9898KCP-20 | CCD Signal Processor with Precision Timing⑩ Generator |
| AD9898KCPRL-20 | TVPS00RF-21-41S W/ PC CON |
| AD9901 | Ultrahigh Speed Phase/Frequency Discriminator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9886KS-140 | 制造商:Rochester Electronics LLC 功能描述:A/D INTERFACE FOR FLAT PANEL, 140 MSPS - Bulk 制造商:Analog Devices 功能描述: |
| AD9887 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Interface for Flat Panel Displays |
| AD9887/PCB | 制造商:Analog Devices 功能描述:INTRFC DUAL FOR FLAT PNL DISPLAYS 160MQFP - Bulk |
| AD9887A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Interface for Flat Panel Displays |
| AD9887A/PCB | 制造商:Analog Devices 功能描述:INTRFC FOR FLAT PNL DISPLAY 16SOIC W - Bulk |
發布緊急采購，3分鐘左右您將得到回復。