- 您現在的位置：買賣IC網 > PDF目錄373971 > AD9927BBCZ (ANALOG DEVICES INC) 14-Bit CCD Signal Processor with V-Driver and Precision TimingTM Generator PDF資料下載
參數資料
| 型號： | AD9927BBCZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | 14-Bit CCD Signal Processor with V-Driver and Precision TimingTM Generator |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, BGA128 |
| 封裝： | 9 X 9 MM, LEAD FREE, MO-225, CSP_BGA-128 |
| 文件頁數： | 66/100頁 |
| 文件大小： | 784K |
| 代理商： | AD9927BBCZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
AD9927
MANUAL SHUTTER OPERATION USING
ENHANCED SYNC MODES
The AD9927 also supports an external signal to control exposure,
using the SYNC input. Generally, the SYNC input is used as an
asynchronous reset signal during master mode operation. When
the enhanced SYNC mode is enabled, the SYNC input provides
additional control of the exposure operation.
Rev. 0 | Page 66 of 100
Normal SYNC Mode (Mode 1)
By default, the SYNC input is used in master mode for
synchronizing the internal counters of the AD9927 with
external timing. The SYNC During Master Mode Operation
section describes how horizontal, vertical, and field designator
signals are reset by the rising edge of the SYNC pulse. Figure 79
also shows how this mode operates, highlighting the behavior of
the mode field designator.
Enhanced SYNC Modes (Modes 2 and 3)
The enhanced SYNC modes can be used to accommodate
unique synchronization requirements during exposure
operations. In SYNC Mode 2, the V and VSG outputs are
suspended and the VD output is masked. The V-outputs are
held at the dc value established by the Sequence 0 start polarities.
There is no SCP operation, but the H-counter is still enabled.
Finally, the AFE sampling clocks, HD, H/RG, CLPOB, HBLK,
are operational and use Sequence 0 behavior. See Figure 80 for
more details.
To enable the enhanced SYNC modes, set the register
ENH_SYNC_EN (Address 0x13 Bit [3]) to 1.
Mode 3 uses all of these features, but the V-outputs are continuous
through the SYNC pulse interval. VD control pulses are masked
during the SYNC interval, and the HD pulse can also be masked,
if required (see Figure 81).
It is important to note that in both of these enhanced modes,
the SYNC pulse resets the counters at both the falling edge and
the rising edge of the SYNC pulse.
Register Update and Field Designator
When using special SYNC Mode 2 or 3, the VD-updated
registers, such as PRIMARY_ACTION, are not updated during
the SYNC interval, and the SCP0 function is ignored and held
at 0 (see Figure 82).
When using either SYNC Mode 2 or 3, both the rising and falling
edges increment the internal field designator; therefore, the new
register data takes effect and VTP information is updated to new
SEQ0 data. However, this does not occur if the MODE register is
to create an output of one field. In that case, the region, sequence,
and group information does not change (see Figure 83).
Shutter Operation in SLR Mode
Referring to Figure 84,
1.
To turn on VSUB, write to the appropriate GP registers to
trigger VSUB and start the manual exposure
[PRIMARY_ACTION = 5]. This change takes effect after
the next VD, and SUBCK is suppressed during the
exposure and readout phases.
2.
To turn on MSHUT during the interval between the next
VD and SYNC, write to the appropriate GP register. When
MSHUT is in the on position, it has line and pixel control.
This change takes effect on the SYNC falling edge since
there is an internal VD.
3.
If the MODE register is programmed to cycle through
multiple fields (5, 7, 3, 5, 7, 3, …, in this example), the internal
field designator increments. If the MODE register is not
required to increment, set up the MODE register such that it
outputs only one field. This prevents the MODE counter
from incrementing during the SYNC interval.
4.
Write to the manual readout trigger to begin the manual
readout [PRIMARY_ACTION = 6]. Write to the
appropriate GP registers to trigger MSHUT to toggle low at
the end of the exposure. This change takes effect on the
SYNC rising edge during readout. Since VD register
update is disabled, the trigger takes effect on the SYNC
rising edge. The MSHUT falling edge is aligned to the
SYNC rising edge. Because the MSHUT falling edge is
aligned with VD, it may be necessary to insert a dummy
VD to delay the readout.
Note that since the internal exposure counter (PRIMARY
counter) is not used during manual SYNC mode operation and
the VD register update is disabled, control is lost on the fine
placement of the GP signals for VSUB, MSHUT, and STROBE
edges while SYNC is low.
New Serial Registers
SYNC Modes 2 and 3 are controlled using the registers listed
in Table 44.
Table 44. Registers for Enhanced SYNC Modes
Register
Length
ENH_SYNC_EN
1b
Description
HI active to enable
(default LO)
HI active to enable masking
(default LO)
HI active to enable masking
(default HI)
HI active to enable masking
(default HI)
SYNC_MASK_V
1b
SYNC_MASK_VD
1b
SYNC_MASK_HD
1b
Note that registers for enhanced SYNC modes are located at
Address 0x13 Bits [6:3].
相關PDF資料 |
PDF描述 |
|---|---|
| AD9927BBCZRL | 14-Bit CCD Signal Processor with V-Driver and Precision TimingTM Generator |
| AD9929BBCZ | CCD Signal Processor with Precision Timing Generator |
| AD9929 | CCD Signal Processor with Precision Timing Generator |
| AD9937 | CCD Signal Processor with Precision Timing⑩ Generator |
| AD9937KCP | CCD Signal Processor with Precision Timing⑩ Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9927BBCZRL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9928 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Channel 14-Bit CCD Signal Processor with V-Driver and Precision Timing Generator |
| AD9928BBCZ | 功能描述:IC CCD SIGNAL PROCESSR 128CSPBGA RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
| AD9928BBCZ-60 | 制造商:Analog Devices 功能描述:- Trays |
| AD9928BBCZRL | 功能描述:IC CCD SIGNAL PROCESSR 128CSPBGA RoHS:否 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
發布緊急采購，3分鐘左右您將得到回復。