欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: GS9090-CNE3
廠商: Gennum Corporation
英文描述: GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI
中文描述: GS9090 GenLINX - R的第三270Mb / s的SDI和DVB解串器,意大利航天局
文件頁數: 43/70頁
文件大小: 696K
代理商: GS9090-CNE3
GS9090 Data Sheet
28201 - 1
July 2005
43 of 70
3.9.7.3 Lock Error Detection
The LOCKED pin of the GS9090 indicates the lock status of the internal reclocker
and lock detect blocks of the device. Only when the LOCKED pin is asserted HIGH
has the device correctly locked to the received data stream (see
Lock Detect on
page 22
).
The GS9090 will also indicate lock error to the host interface when LOCKED =
LOW by setting the LOCK_ERR bit in the ERROR_STATUS register HIGH.
3.9.7.4 Ancillary Data Checksum Error Detection
The GS9090 will calculate checksums for all received ancillary data and compare
the calculated values to the received checksum words. If a mismatch is detected,
the CS_ERR bit of the ERROR_STATUS register will be set HIGH.
Although the GS9090 will calculate and compare checksum values for all ancillary
data types by default, the host interface may program the device to check only
certain types of ancillary data checksums. This is accomplished via the
ANC_TYPE registers as described in
Programmable Ancillary Data Detection on
page 31
.
3.9.7.5 TRS Error Detection
TRS error flags are generated by the GS9090 when:
1. The received TRS H timing does not correspond to the internal flywheel
timing; or
2. The received TRS hamming codes are incorrect.
Both 8-bit and 10-bit SAV and EAV TRS words are checked for timing and data
integrity errors. These are flagged via the SAV_ERR and/or EAV_ERR bits of the
ERROR_STATUS register.
NOTE: H timing based TRS errors will only be generated if the FW_EN pin is set
HIGH. F & V timing errors are not detected or corrected.
3.9.8 Error Correction and Insertion
In addition to signal error detection and indication, the GS9090 may also correct
certain types of errors by inserting corrected code words, checksums, and TRS
values into the data stream. These features are only available in SMPTE mode and
the IOPROC_EN pin must be set HIGH by the application layer. Individual
correction features may be enabled or disabled by setting bits 0 to 3 in the
IOPROC_DISABLE register (
Table 3-14
).
All of the IOPROC_DISABLE register bits default to '0' after a device reset,
enabling all of the processing features. To disable any individual error correction
feature, the host interface must set the corresponding bit HIGH in the
IOPROC_DISABLE register.
相關PDF資料
PDF描述
GS9092A GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI
GS9092ACNE3 GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI
GS9092 GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI
GS9092-CNE3 GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI
GSC9620 P-CHANNEL ENHANCEMENT MODE POWER MOSFET
相關代理商/技術參數
參數描述
GS9091B 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX II 270Mb/s Deserializer for SDI and DVB-ASI
GS9091BCBE3 功能描述:RF, RFID, WIRELESS RoHS:是 類別:集成電路 (IC) >> 接口 - 串行器,解串行器 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 功能:解串器 數據速率:2.5Gbps 輸入類型:串行 輸出類型:并聯 輸入數:- 輸出數:24 電源電壓:1.8 V ~ 3.3 V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP(10x10) 包裝:管件
GS9092 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI
GS9092A 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI
GS9092A_10 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Serializer for SDI and DVB-ASI
主站蜘蛛池模板: 石泉县| 寿宁县| 克拉玛依市| 通渭县| 都安| 白水县| 河北区| 罗田县| 雷山县| 呼和浩特市| 大连市| 凤翔县| 图木舒克市| 临邑县| 东平县| 安图县| 章丘市| 临洮县| 桃江县| 普兰店市| 黔西县| 清远市| 锦屏县| 当阳市| 灵台县| 会东县| 青岛市| 武威市| 凌云县| 庆云县| 万全县| 东丰县| 南溪县| 稷山县| 安康市| 仙游县| 上林县| 博白县| 香河县| 保康县| 唐河县|