- 您現在的位置：買賣IC網 > PDF目錄385345 > GS9090-CNE3 (Gennum Corporation) GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI PDF資料下載
參數資料
| 型號： | GS9090-CNE3 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI |
| 中文描述： | GS9090 GenLINX - R的第三270Mb / s的SDI和DVB解串器，意大利航天局 |
| 文件頁數： | 51/70頁 |
| 文件大小： | 696K |
| 代理商： | GS9090-CNE3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
GS9090 Data Sheet
28201 - 1
July 2005
51 of 70
3.10.3 Ancillary Data Extraction Mode
The internal FIFO is ancillary data extraction mode when the application layer sets
the FIFO_EN and IOPROC_EN pins HIGH, and the FIFO_MODE[1:0] bits in the
IOPROC_DISABLE register are configured to 10b.
Once the FIFO enters ancillary data extraction mode, it takes 2200 PCLKs (82us)
to initialize the FIFO before ancillary data extraction can begin.
In this mode, the FIFO is divided into two separate blocks of 1024 words each. This
allows ancillary data to be written to one side of the FIFO while the application layer
reads from the other. Thus, in each half of the FIFO, the GS9090 will write the
contents of the packets up to a maximum of 1024 8-bit words.
As described in
Programmable Ancillary Data Detection on page 31
, up to five
specific types of ancillary data to be extracted can be programmed in the
ANC_TYPE registers. If the ANC_TYPE registers are all set to zero, the device will
extract all types of ancillary data.
The entire packet, including the ancillary data flag (ADF), data identification (DID),
secondary data identification (SDID), data count (DC), and checksum word will be
written into the memory. The device will detect ancillary data packet DID's placed
anywhere in the video data stream, including the active picture area.
Additionally, the lines from which the packets are to be extracted from can be
programmed into the ANC_LINE_A[10:0] and ANC_LINE_B[10:0] registers,
allowing ancillary data from a maximum of two lines per frame to be extracted. If
only one line number register is programmed (with the other set to zero), ancillary
data packets will be extracted from one line per frame only. When both registers
are set to zero, the device will extract packets from all lines.
The application layer reads the extracted ancillary data through the host interface
starting at address 02Ch up to 42Bh inclusive (1024 words). This must be done
while there is a valid video signal present at the serial input and the device is locked
(LOCKED = HIGH).
3.10.3.1 Ancillary Data Extraction and Reading
To start ancillary data extraction, the ANC_PKT_EXT bit of the IOPROC_DISABLE
register must be set HIGH (see
Table 3-14
in
Error Correction and Insertion on
page 43
). Packet extraction will begin in the following frame after this bit has been
set HIGH.
NOTE: Ancillary data extraction will not begin until 2200 PCLKs (82us) after the
device has entered into ancillary data extraction mode (FIFO_MODE[1:0] = 10b),
regardless of the setting of the ANC_PKT_EXT bit.
When the FIFO is configured for ancillary data extraction mode, setting the
IOPROC_EN pin LOW will disable packet extraction. If IOPROC_EN is LOW, the
setting of the ANC_PKT_EXT host interface bit will be ignored.
相關PDF資料 |
PDF描述 |
|---|---|
| GS9092A | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092ACNE3 | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092-CNE3 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GSC9620 | P-CHANNEL ENHANCEMENT MODE POWER MOSFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9091B | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX II 270Mb/s Deserializer for SDI and DVB-ASI |
| GS9091BCBE3 | 功能描述:RF, RFID, WIRELESS RoHS:是 類別:集成電路 (IC) >> 接口 - 串行器，解串行器 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 功能:解串器 數據速率:2.5Gbps 輸入類型:串行 輸出類型:并聯 輸入數:- 輸出數:24 電源電壓:1.8 V ~ 3.3 V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:管件 |
| GS9092 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092A | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092A_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Serializer for SDI and DVB-ASI |
發布緊急采購，3分鐘左右您將得到回復。