- 您現在的位置：買賣IC網 > PDF目錄382301 > MC4GH02GNMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC4GH02GNMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 73/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC4GH02GNMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁當前第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
73
Sep.22.2005
Revision 0.3
Data transfer mode.
After a card receives its RCA it will switch to data transfer mode. In this mode the CMD line is driven with push-pull drivers.
The command is followed by a period of two Z bits (allowing time for direction switching on the bus) and than by P bits
pushed up by the responding card. This timing diagram is relevant for all responded host commands except CMD1,2,3:
Figure 6-9 : Command Response Timing (Data Transfer Mode)
R1b Responses
Some commands, like CMD6, may assert the BUSY signal after responding with R1. If the busy signal is asserted, it is
done two clock cycles after the end bit of the command. the DAT0 line is driven low, DAT1-DAT7 lines are driven by the
card though their value is not relevant.
Figure 6-10 : R1b Response Timing
Last Card Response - Next Host Command Timing
After receiving the last card response, the host can start the next command transmission after at least N
RC
clock cycles.
This timing is relevant for any host command.
Figure 6-11 : Timing Response End To Next Command Start (Data Transfer Mode)
Last Host Command - Next Host Command Timing
After the last command has been sent, the host can continue sending the next command after at least N
CC
clock periods.
If the ALL_SEND_CID command is not responded by the card after N
ID
+ 1 clock periods, the host can conclude there is
no card present in the bus.
Figure 6-12 : Timing Of Command Sequences (All Modes)
←
Host Command
→
←
N
CR
cycles
→
←
S T
content
CRC E Z Z P * * * P S T
Response
content
→
CRC E Z Z Z
CMD
←
Host Command
→
S T
content
CMD
CRC E Z Z Z Z Z
←
N
ST
→
←
Card Is Busy
→
Z Z Z Z Z Z Z Z Z Z Z Z S L
Z Z Z Z Z Z Z Z Z Z Z Z X
* * * * * * * * * * * * * * * * * * * * * * * *
* * * * * * * * * * * * * * * * * * * *
Z Z Z Z Z
DAT0
DAT1-7
* * * * * * * * * * * * * * * * * * * * * *
E Z Z Z
X Z Z Z
←
Response
→
←
N
CR
cycles
→
←
Host Command
→
S T
content
CRC E Z
* * *
CMD
Z S T
content
CRC E Z Z
←
Host Command
→
←
N
CC
cycles
→
←
Host Command
→
S T
content
CRC E Z
* * *
CMD
Z S T
content
CRC E Z Z
相關PDF資料 |
PDF描述 |
|---|---|
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
| MC2300 | Navigator Motion Processor |
| MC26LS30 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
| MC26LS30D | CABLE GLAND, PG29 |
| MC26LS30DR2 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC4M | 制造商:G & J HALL 功能描述:STEP DRILL MULTICUT 4-12MM X 2MM 制造商:G & J HALL 功能描述:STEP DRILL, MULTICUT, 4-12MM X 2MM |
| MC-4-MALE | 制造商:Multi-Contact USA 功能描述: |
| MC4MANUAL | 制造商:Omron Corporation 功能描述: |
| MC-4R128CEE6B | 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT |
| MC-4R128CEE6B-653 | 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT |
發布緊急采購，3分鐘左右您將得到回復。