- 您現在的位置：買賣IC網 > PDF目錄382301 > MC4GH02GNMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC4GH02GNMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 88/102頁 |
| 文件大?。?/td> | 1384K |
| 代理商： | MC4GH02GNMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁當前第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
88
Sep.22.2005
Revision 0.3
7.14 Read ahead in Multiple Block read operation
In Multiple Block read operations, in order to improve read performance, the card may fetch data from the memory array,
ahead of the host. In this case, when the host is reading the last addresses of the memory, the card attempts to fetch data
beyond the last physical memory address and generates an ADDRESS_OUT_OF_RANGE error.
Therefore, even if the host times the stop transmission command to stop the card immediately after the last byte of data
was read, the card may already have generated the error, and it will show in the response to the stop transmission com-
mand. The host should ignore this error.
7.15 Memory Array Partitioning
Same as for MultiMediaCard mode.
7.16 Card Lock/unlock Operation
Usage of card lock and unlock commands in SPI mode is identical to MultiMediaCard mode. In both cases, the command
response is of type R1b. After the busy signal clears, the host should obtain the result of the operation by issuing a
GET_STATUS command. Please refer to Chapter 6.2.10 for details.
7.17 SPI Command Set
7.17.1
Command Format
All the MultiMediaCard commands are 6 bytes long. The command transmission always starts with the left bit of the bit-
string corresponding to the command codeword. All commands are protected by a CRC. The commands and arguments
are listed in Table 7-5.
7.17.2
Command Classes
As in MultiMediaCard mode, the SPI commands are divided into several classes (See Table 7-4). Each class supports a
set of card functions. A MultiMediaCard will support the same set of optional command classes in both communication
modes (there is only one command class table in the CSD register). The available comand classes, and the supported
command for a specific class, however, are different in the MultiMediaCard and the SPI communication mode.
Bit position
Width (bits)
Value
Description
47
1
‘0’
46
1
‘1’
[45:40]
6
x
[39:8]
32
x
argument
[7:1]
7
x
CRC7
0
1
‘1’
start bit
transmission bit
Table 7-3 : Command format in SPI Mode
command index
end bit
相關PDF資料 |
PDF描述 |
|---|---|
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
| MC2300 | Navigator Motion Processor |
| MC26LS30 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
| MC26LS30D | CABLE GLAND, PG29 |
| MC26LS30DR2 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC4M | 制造商:G & J HALL 功能描述:STEP DRILL MULTICUT 4-12MM X 2MM 制造商:G & J HALL 功能描述:STEP DRILL, MULTICUT, 4-12MM X 2MM |
| MC-4-MALE | 制造商:Multi-Contact USA 功能描述: |
| MC4MANUAL | 制造商:Omron Corporation 功能描述: |
| MC-4R128CEE6B | 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT |
| MC-4R128CEE6B-653 | 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT |
發布緊急采購，3分鐘左右您將得到回復。