- 您現在的位置：買賣IC網 > PDF目錄382301 > MC4GH02GNMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC4GH02GNMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 85/102頁 |
| 文件大?。?/td> | 1384K |
| 代理商： | MC4GH02GNMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
85
Sep.22.2005
Revision 0.3
Multiple block write with pre-defined block count
The card will accept the requested number of data blocks and terminate the transaction. ‘Stop tran’ token is not required at
the end of this type of multiple block write, unless terminated with an error. In order to start a multiple block write with pre-
defined block count the host must use the SET_BLOCK_COUNT command (CMD23) immediately preceding the
WRITE_MULTIPLE_BLOCK (CMD25) command. Otherwise the card will start an open-ended multiple block write which
can be stopped using the ‘Stop tran’ token.
The host can abort writing at any time, within a multiple block operation, regardless of the its type. Transaction abort is
done by sending the ‘Stop tran’ token. If a multiple block write with pre-defined block count is aborted, the data in the
remaining blocks is not defined.
If the host provides an out of range address as an argument to either CMD17 or CMD18, or the currently defined block
length is illegal for a read operation, the card will reject the command, remain in
Tran
state and respond with the
ADDRESS_OUT_OF_RANGE or BLOCK_LEN_ERROR bit set, respectively.
If the host sets the argument of the SET_BLOCK_COUNT command (CMD23) to all 0s, then the command is accepted;
however, a subsequent write will follow the open-ended multiple block write protocol (STOP_TRANSMISSION command -
CMD12 - is required).
If the card detects a CRC error or a programming error (e.g. write protect violation, out of range, address misalignment,
internal error, etc.) during a multiple block write operation (both types) it will report the failure in the data-response token
and ignore any further incoming data blocks. The host must than abort the operation by sending the ‘Stop Tran’ token.
If the host uses partial blocks whose accumulated length is not block aligned, and block misalignment is not allowed (CSD
parameter WRITE_BLK_MISALIGN is not set), the card shall detect the block misalignment error during the reception of
the first misaligned block, abort the write operation, and ignore all further incoming data. The host must abort the operation
by sending the ‘Stop Tran’ token, to which the card will respond with the ADDRESS_MISALIGN bit set.
Once the programming operation is completed (either successfully or with an error), the host must check the results of the
programming (or the cause of the error if already reported in the data-response token) using the SEND_STATUS com-
mand (CMD13).
If the host sends a ‘Stop Trans’ token after the card received the last data block of a multiple block operation with pre-
defined number of blocks, it will be interpreted as the beginning of an illegal command and responded accordingly.
While the card is busy, resetting the CS signal will not terminate the programming process. The card will release the
DataOut line (tri-state) and continue with programming. If the card is reselected before the programming is finished, the
DataOut line will be forced back to low and all commands will be rejected.
Resetting a card (using CMD0) will terminate any pending or active programming operations. This may destroy the data
formats on the card. It is in the responsibility of the host to prevent it.
7.9 Erase & Write Protect Management
The erase and write protect management procedures in the SPI mode are identical to those of the MultiMediaCard mode.
While the card is erasing or changing the write protection bits of the predefined erase groups list, it will be in a busy state
and hold the DataOut line low. Figure 7-7 illustrates a ‘no data’ bus transaction with and without busy signalling.
Figure 7-7 : SPI ‘No data’ Operations
command
command
DataIn
DataOut
from
host
to card
from
host
to card
from
card
to host
response
response
from
card
to host
busy
相關PDF資料 |
PDF描述 |
|---|---|
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
| MC2300 | Navigator Motion Processor |
| MC26LS30 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
| MC26LS30D | CABLE GLAND, PG29 |
| MC26LS30DR2 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC4M | 制造商:G & J HALL 功能描述:STEP DRILL MULTICUT 4-12MM X 2MM 制造商:G & J HALL 功能描述:STEP DRILL, MULTICUT, 4-12MM X 2MM |
| MC-4-MALE | 制造商:Multi-Contact USA 功能描述: |
| MC4MANUAL | 制造商:Omron Corporation 功能描述: |
| MC-4R128CEE6B | 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT |
| MC-4R128CEE6B-653 | 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT |
發布緊急采購，3分鐘左右您將得到回復。