- 您現在的位置：買賣IC網 > PDF目錄382345 > MPC823 (Motorola, Inc.) Communication Processor Module PDF資料下載
參數資料
| 型號： | MPC823 |
| 廠商： | Motorola, Inc. |
| 英文描述： | Communication Processor Module |
| 中文描述： | 通信處理器模塊 |
| 文件頁數： | 15/74頁 |
| 文件大小： | 234K |
| 代理商： | MPC823 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
Communication Processor Module
MOTOROLA
MPC823 REFERENCE MANUAL
16-393
S
C
1
P
16.11.6.6 SMCx UART COMMANDS.
You can program the CPM command register
(CPCR) with the following commands to transmit data.
STOP TRANSMIT
—This command disables the transmission of characters on the
transmit channel. If the SMCx UART controller receives this command while
transmitting a message, it stops transmitting. The SMCx UART controller finishes
transmitting any data that has already been transferred to its FIFO and shift register and
then stops transmitting data. The TBPTR is not advanced when this command is
issued. The SMCx UART controller transmits a programmable number of break
sequences and then transmits idles. The number of break sequences, which can be
zero, must be written to the BRKCR entry before this command is issued to the SMCx
UART controller.
RESTART TRANSMIT
—This command enables characters to be transmitted on the
transmit channel. The SMCx UART controller expects it after disabling the channel in
its SMCMR and after issuing the
STOP TRANSMIT
command. The SMCx UART
controller resumes transmission from the current TBPTR in the channel’s transmit
buffer descriptor table.
INIT TX PARAMETERS
—This command initializes all the transmit parameters in this
serial channel’s parameter RAM to their reset state and must only be issued when the
transmitter is disabled. The
INIT TX
AND
RX PARAMS
command can also be used to
reset the transmit and receive parameters.
You can program the CPCR with the following commands to receive data.
ENTER HUNT MODE
—This command cannot be used for an SMCx UART channel.
Issue the
CLOSE RX BD
command instead.
CLOSE RX BD
—This command is used to force a serial management controller to
close the current receive buffer descriptor if it is currently being used and to use the next
buffer descriptor in the list for any subsequently received data. If a serial management
controller is not in the process of receiving data, no action is taken by this command.
INIT RX PARAMETERS
—This command initializes all the receive parameters in this
serial channel parameter RAM to their reset state. This command must only be issued
when the receiver is disabled. The
INIT TX AND RX PARAMS
command can also be
used to reset the receive and transmit parameters.
16.11.6.7 SENDING A BREAK.
A break is an all-zeros character without stop bits and it is
sent by issuing the
STOP TRANSMIT
command. The SMCx UART controller finishes
transmitting any outstanding data and then sends a character with consecutive zeros. The
number of zero bits in this character is the sum of the character length, plus the number of
start, parity, and stop bits. The SMCx UART controller transmits a programmable number of
break characters according to the BRKCR entry and then reverts to idle or sends data if the
RESTART TRANSMIT
command was issued before completion. When the break is
completed, the transmitter sends at least one idle character before transmitting any data to
guarantee recognition of a valid start bit.
相關PDF資料 |
PDF描述 |
|---|---|
| MPC823UM_REV1_16-CPM7 | 10 AMP SUBMINIATURE POWER RELAY |
| MPC9109 | LOW VOLTAGE 1:18 CLOCK DISTRIBUTION CHIP |
| MPC9229 | 400 MHz Low Voltage PECL Clock Synthesizer |
| MPC9230 | 800 MHz Low Voltage PECL Clock Synthesizer |
| MPC9350 | LOW VOLTAGE PLL CLOCK DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC823CVR66B2T | 功能描述:微處理器 - MPU POWER QUICC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC823CZQ66B2T | 功能描述:微處理器 - MPU PORTABLE SYSTEM MPU RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC823CZQ66B2T | 制造商:Freescale Semiconductor 功能描述:IC 32-BIT MPU 66MHZ 256-PBGA |
| MPC823ELD | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MPC823e Mobile Computing Microprocessor |
| MPC823ELE | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MPC823e Mobile Computing Microprocessor |
發布緊急采購，3分鐘左右您將得到回復。