欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: S29CL032J0RFFN130
廠商: SPANSION LLC
元件分類: PROM
英文描述: 1M X 32 FLASH 3.3V PROM, 48 ns, PBGA80
封裝: 13 X 11 MM, 1 MM PITCH, LEAD FREE, FORTIFIED, BGA-80
文件頁數: 29/78頁
文件大小: 1825K
代理商: S29CL032J0RFFN130
September 27, 2006 S29CD-J_CL-J_00_B1
S29CD-J & S29CL-J Flash Family
33
Pr el im i n a r y
Notes:
In this mode, the write protection function is bypassed unless the
PPB Lock Bit = 1.
The ACC pin must not be at VHH for operations other than acceler-
ated programming and accelerated chip erase, or device damage
may result.
The ACC pin must not be left floating or unconnected; inconsistent
behavior of the device may result.
The Accelerated Program command is not permitted if the Secured
Silicon sector is enabled.
8.7.7
Unlock Bypass
The device features an Unlock Bypass mode to facilitate faster programming, erasing (Sector and
Chip Erase), as well as CFI commands. Once the device enters the Unlock Bypass mode, only
two write cycles are required to program or erase data, instead of the normal four cycles. This
results in faster total programming/erasing time.
Command Definitions on page 71 shows the requirements for the unlock bypass command
sequences.
During the unlock bypass mode only the Read, Unlock Bypass Program and Unlock Bypass Reset
commands are valid. To exit the unlock bypass mode, the system must issue the two-cycle un-
lock bypass reset command sequence, which returns the device to read mode.
Notes:
1. The Unlock Bypass Command is ignored if the Secured Silicon sector is enabled.
2. Unlike the standard program or erase commands, there is no Unlock Bypass Program/Erase
Suspend or Program/Erase Resume command.
8.7.8
Simultaneous Read/Write
The simultaneous read/write feature allows the host system to read data from one bank of mem-
ory while programming or erasing in another bank of memory.
The Simultaneous Read/Write feature can be used to perform the following:
Programming in one bank, while reading in the other bank
Erasing in one bank, while reading in the other bank
Programming a PPB, while reading data from the large bank or status from the small bank
Erasing a PBB, while reading data from the large bank or status from the small bank
Any of the above situations while in the Secured Silicon Sector Mode
The Simultaneous R/W feature can not be performed during the following modes:
CFI Mode
Password Program operation
Password Verify operation
As an alternative to using the Simultaneous Read/Write feature, the user may also suspend an
erase or program operation to read in another location within the same bank (except for the sec-
tor being erased).
8.8
Write Operation Status
The device provides several bits to determine the status of a program or erase operation. The
following subsections describe the function of DQ7, DQ6, DQ2, DQ5, DQ3, and RY/BY#.
相關PDF資料
PDF描述
S29CL032J1JFAI110 1M X 32 FLASH 3.3V PROM, 54 ns, PBGA80
S29CL032J1MFAN120 1M X 32 FLASH 3.3V PROM, 54 ns, PBGA80
S29CL032J0PQAN102 1M X 32 FLASH 3.3V PROM, 54 ns, PQFP80
S29GL016A10FAI020 1M X 16 FLASH 3V PROM, 100 ns, PBGA64
S29GL032A10TAIR10 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
相關代理商/技術參數
參數描述
S29GL016A 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
S29GL016A100BAI010 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
S29GL016A100BAI012 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
S29GL016A100BAI013 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
S29GL016A100BAIR10 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
主站蜘蛛池模板: 定南县| 普兰县| 长泰县| 永嘉县| 剑阁县| 兴海县| 甘肃省| 雅江县| 乐至县| 武冈市| 贵港市| 巴林左旗| 南开区| 青海省| 安顺市| 吴忠市| 光泽县| 舞阳县| 安西县| 达拉特旗| 东阿县| 焦作市| 大方县| 涟源市| 若尔盖县| 三台县| 龙山县| 兰溪市| 福州市| 新余市| 宝丰县| 合江县| 巨野县| 无极县| 外汇| 彝良县| 邵阳县| 营山县| 磐石市| 赫章县| 荥阳市|