欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TMC222-SI
元件分類: 運動控制電子
英文描述: STEPPER MOTOR CONTROLLER, PDSO20
封裝: SOIC-20
文件頁數: 19/48頁
文件大小: 457K
代理商: TMC222-SI
26
TMC222 DATASHEET (V. 1.12 / March 7, 2011)
Copyright 2004-2011 TRINAMIC Motion Control GmbH & Co. KG
Every byte put on the SDA line must have a length of 8 bits, where the most significant bit (MSB) is
transferred first. The number of bytes that can be transmitted to the TCM222 is restricted to 8 bytes.
Each byte is followed by an acknowledge bit, which is issued by the receiving node (see figure below).
SDA
SCL
1
2
7
8
9
1
START
condition
STOP
condition
MSB
ACK
Figure 17: Two Wire Serial Interface - Data Transfer
6.3
Physical Address of the circuit
The circuit must be provided with a physical address in order to discriminate this circuit from other
ones on the serial bus. This address is coded on seven bits (two bits are internally hardwired to ‘1’),
yielding the theoretical possibility of 32 different circuits on the same bus. It is a combination of four
OTP memory bits (see Table 9 : OTP Memory Structure) and one hardwired address bit (pin HW). HW
must either be connected to ground or Vbat. When HW is not connected and left floating correct
functionality of the serial interface is not guaranteed. Pin HW uses the same principle to check whether
it is connected to ground or Vbat like the SWI input (see 5.1.9 External Switch).
The TMC222 supports a “general call” address. Therefore the circuit is addressable using either the
physical slave address or address “000 0000”.
Physical address
OTP Memory
Hardwired Bit
(Connect to 0 or 1)
OTP_AD3
OTP_AD1
OTP_AD2
OTP_AD0
'1'
AD5
AD6
AD1
AD2
AD3
AD4
AD0
HW2
Figure 18: Two Wire Serial Interface - Physical Address resp. Address Field
With un-programmed OTP address bits (OTP_AD3=o, OTP_AD2=o, OTP_AD1=o, OTP_AD0=o) and
HW='0' (pin HW @ GND), the slave address resp. the address field of the TMC222 for reading is
11oooo01 (0xC1, 193) and for writing the slave address resp. the address field is 11oooo00 (0xC0,
192). The LSB of the address field selects read (='1') and write (='0'). With un-programmed OTP
address bits and HW='1' (pin HW @ Vbat), the slave address resp. the address field of the TMC222
for reading is 11oooo11 (0xC3, 195) and for writing the salve address resp. the address field is
11oooo10 (0xC2, 194).
Important Hint: The HW is not a logic level input as usual; it needs to be connected via 1K resistor
either to +VBAT or GND;
6.4
Write data to TMC222
A complete datagram consists of the following: a Start condition, the slave address (7 bit), a read/write
bit (‘0’ = write, ‘1’ = read), an acknowledge bit, a number of data bytes (8 bit) each followed by an
acknowledge bit, and a Stop condition. The acknowledge bit is used to signal to the transmitter the
correct reception of the preceding byte, in this case the TMC222 pulls the SDA line low.
The TMC222 reads the incoming data at SDA with every rising edge of the SCL line. To finish the
transmission the master has to transmit a Stop condition. Some commands for the TMC222 are
supporting eight bytes of data, other commands are transmitting two bytes of data.
相關PDF資料
PDF描述
TMC222-LI STEPPER MOTOR CONTROLLER, QCC32
TMC222-PI20 STEPPER MOTOR CONTROLLER, PDSO20
TMC22290R2C COLOR SIGNAL ENCODER, PQCC44
TMC22291R2C COLOR SIGNAL ENCODER, PQCC44
TMC2301G8A1 SPECIALTY CONSUMER CIRCUIT, CPGA68
相關代理商/技術參數
參數描述
TMC223-EVAL 制造商:Trinamic 功能描述:EVAL MODULE FOR TMC223
TMC223-LI 制造商:Trinamic 功能描述: 制造商:Trinamic 功能描述:IC MOTOR CTRLR/DVR I2C 32QFN
TMC223-SI 制造商:Trinamic 功能描述:Bulk
TMC2242 WAF 制造商:Fairchild Semiconductor Corporation 功能描述:
TMC2242A 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Digital Half-Band Interpolating/Decimating Filter 12-bit In/16-bit Out, 60 MHz
主站蜘蛛池模板: 阿克苏市| 扶余县| 高密市| 托克托县| 抚顺县| 潜江市| 宿松县| 义乌市| 吴堡县| 柏乡县| 板桥市| 丰顺县| 绥棱县| 苏州市| 彰武县| 砚山县| 蕲春县| 盐池县| 嘉禾县| 彭阳县| 波密县| 元朗区| 枣强县| 吉水县| 郸城县| 夹江县| 保山市| 台山市| 根河市| 澎湖县| 江津市| 都江堰市| 通州市| 施甸县| 古蔺县| 本溪| 织金县| 和硕县| 留坝县| 阜平县| 互助|