- 您現在的位置：買賣IC網 > PDF目錄98265 > TMC222-SI STEPPER MOTOR CONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | TMC222-SI |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, PDSO20 |
| 封裝： | SOIC-20 |
| 文件頁數： | 30/48頁 |
| 文件大小： | 457K |
| 代理商： | TMC222-SI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
36
TMC222 DATASHEET (V. 1.12 / March 7, 2011)
Copyright 2004-2011 TRINAMIC Motion Control GmbH & Co. KG
6.9
Positioning Task Example
The TMC222 has to perform a positioning task, where the actual position of the stepper motor is
unknown. The desired target position is 3000 steps away from position 0. See figure below.
X [steps]
Stop
Actual
Position
=
unknown
Target
Position
= 3000
Position 0
?
Figure 22: Positioning Example: Initial situation
The following sequence of commands has to be sent to the slave in order to complete the scenario
described above (assumed after power on):
GetFullStatus1
The command is used to read the current status of the TMC222. Electrical or environmental problems
will be reported, furthermore the circuit leaves the shutdown state and is ready for action. See 6.8.1
GetFullStatus1 on page 30.
GetFullStatus2
The circuit will enter a deadlock state if the actual position corresponds to the first target position of the
RunInit command. This command is used to read the actual position. The master must take care that
both positions are containing different values. For deadlock conditions see 5.1.11 Reference Search /
Position initialization on page 14.
SetMotorParam
In order to drive the stepper motor with a desired motion parameters like torque, velocity, aso. the
SetMotorParam command must issued. See 6.8.9 SetMotorParam on page 34.
RunInit
Hence the actual position is unknown, a position initialization has to be performed. The first motion
must drive the stepper motor into the stop for sure. The second motion is a very short motion to bring
the motor out of the stop. The actual position is then set to zero automatically after the second motion
is finished. See 6.8.8 RunInit on page 33.
After reference search the situation is as depicted in the figure below. Actual position of the stepper
motor corresponds to zero, the target position is 3000 steps away from the actual position.
X [steps]
Stop
Actual
Position
= 0
Target
Position
= 3000
Figure 23: Positioning Example: Situation after reference search
Now the positioning command SetPosition can be issued in order to drive the stepper motor to the
desired position.
相關PDF資料 |
PDF描述 |
|---|---|
| TMC222-LI | STEPPER MOTOR CONTROLLER, QCC32 |
| TMC222-PI20 | STEPPER MOTOR CONTROLLER, PDSO20 |
| TMC22290R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC22291R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC2301G8A1 | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC223-EVAL | 制造商:Trinamic 功能描述:EVAL MODULE FOR TMC223 |
| TMC223-LI | 制造商:Trinamic 功能描述: 制造商:Trinamic 功能描述:IC MOTOR CTRLR/DVR I2C 32QFN |
| TMC223-SI | 制造商:Trinamic 功能描述:Bulk |
| TMC2242 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| TMC2242A | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Digital Half-Band Interpolating/Decimating Filter 12-bit In/16-bit Out, 60 MHz |
發布緊急采購，3分鐘左右您將得到回復。