- 您現在的位置：買賣IC網 > PDF目錄98265 > TMC222-SI STEPPER MOTOR CONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | TMC222-SI |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, PDSO20 |
| 封裝： | SOIC-20 |
| 文件頁數： | 47/48頁 |
| 文件大小： | 457K |
| 代理商： | TMC222-SI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁
8
TMC222 DATASHEET (V. 1.12 / March 7, 2011)
Copyright 2004-2011 TRINAMIC Motion Control GmbH & Co. KG
5
Functional Description
5.1
Position Controller and Main Controller
5.1.1
Stepping Modes
The TMC222 supports up to 16 micro steps per full step, which leads to smooth and low torque ripple
motion of the stepping motor. Four stepping modes (micro step resolutions) are selectable by the user
(see also Table 11):
Half step Mode
1/4 Micro stepping
1/8 Micro stepping
1/16 Micro stepping
5.1.2
Velocity Ramp
A common velocity ramp where a motor drives to a desired position is shown in the figure below. The
motion consists of a acceleration phase, a phase of constant speed and a final deceleration phase.
Both the acceleration and the deceleration are symmetrical. The acceleration factor can be chosen
from a table with 16 entries. (Table 5: Acc Parameter on page 11). A typical motion begins with a start
velocity Vmin. During acceleration phase the velocity is increased until Vmax is reached. After
acceleration phase the motion is continued with velocity Vmax until the velocity has to be decreased in
order to stop at the desired target position. Both velocity parameters Vmin and Vmax are
programmable, whereas Vmin is a programmable ratio of Vmax. (See Table 3: Vmax Parameter on
page 10 and Table 4: Vmin on page 11). The user has to take into account that Vmin is not allowed to
change while a motion is ongoing. Vmax is only allowed to change under special circumstances. (See
5.1.4 Vmax Parameter on page 10).
The peak current value to be fed to each coil of the stepper-motor is selectable from a table with 16
possible values. It has to be distinguished between the run current Irun and the hold current Ihold. Irun
is fed through the stepper motor coils while a motion is performed, whereas Ihold is the current to hold
the stepper motor before or after a motion. More details about Irun and Ihold can be found in 5.3.1. and
5.3.2.
Velocity resp. acceleration parameters are accessable via the serial interface. These parameters are
written via the SetMotorParam command (see 6.8.9) and read via the GetFullStatus1 command (see
6.8.1).
time
[s]
Velocity V
[FS/s]
V
max
V
min
X
start
X
target
No
Movement
Acceleration
Phase
Constant Velocity
Deceleration
Phase
No
Movement
State of Motion
相關PDF資料 |
PDF描述 |
|---|---|
| TMC222-LI | STEPPER MOTOR CONTROLLER, QCC32 |
| TMC222-PI20 | STEPPER MOTOR CONTROLLER, PDSO20 |
| TMC22290R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC22291R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC2301G8A1 | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC223-EVAL | 制造商:Trinamic 功能描述:EVAL MODULE FOR TMC223 |
| TMC223-LI | 制造商:Trinamic 功能描述: 制造商:Trinamic 功能描述:IC MOTOR CTRLR/DVR I2C 32QFN |
| TMC223-SI | 制造商:Trinamic 功能描述:Bulk |
| TMC2242 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| TMC2242A | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Digital Half-Band Interpolating/Decimating Filter 12-bit In/16-bit Out, 60 MHz |
發布緊急采購，3分鐘左右您將得到回復。