- 您現在的位置：買賣IC網 > PDF目錄98286 > TPS65820RSHTG4 (TEXAS INSTRUMENTS INC) 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 PDF資料下載
參數資料
| 型號： | TPS65820RSHTG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| 封裝： | 7 X 7 MM, GREEN, PLASTIC, QFN-56 |
| 文件頁數： | 68/98頁 |
| 文件大小： | 2290K |
| 代理商： | TPS65820RSHTG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁當前第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁
External Trigger Operation
Detecting an External Trigger Event
GPIO3
INTERNAL ADC
CONVERSIONSTART
CONVERTER
MODE
ARMED
CONVERTING
TDLY(TRG)
Executing Multiple Sample Cycles With an External Trigger
SLVS663B – MAY 2006 – REVISED APRIL 2008 .............................................................................................................................................................. www.ti.com
The value loaded in the I2C registers ADC READING_HI and ADC READING_LO at the end of a conversion
cycle is defined by control bits ADC_READ0 and ADC_READ1 in register ADC READING_HI. The average,
minimum, maximum and last sample values for a conversion cycle can be read if the external host executes an
I2C write operation, changing the values of bits ADC_READ0 and ADC_READ1, followed by an I2C read
operation on registers ADC READING_HI and ADC READING_LO. The minimum, maximum, average, and last
values have the same value if a conversion cycle with only one sample is executed.
The ADC_READ0 and ADC_READ1 bits can not be modified during the execution of a conversion cycle. A new
conversion cycle should be started only after the current conversion cycle is completed, by toggling the ADC_EN
bit from HI to LO and HI again.
The trigger control circuit can be programmed to use an external signal to start a conversion. The TPS65820
GPIO3 input is configurable as an ADC trigger, with ADC conversion starting on either a rising edge or falling
edge. When using an external trigger the trigger delay, trigger wait time delay and trigger holdoff mode can be
programmed using I2C registers.
The procedure to start an externally-triggered conversion cycle has the following steps:
1. Verify that the current conversion cycle has ended (ADC_STATUS=LO, I2C register ADC_READING_HI)
2. Set ADC_EN=LO
3. Configure ADC sampling mode, ALU mode, trigger parameters, etc.
4. Set ADC_EN=HI
After step 4 the ADC is armed, waiting for an external trigger detection to start a conversion cycle. Similarly to
the non-triggered mode, the ADC configuration should not be modified until the current conversion cycle ends.
Note that in the external trigger mode the current cycle does not end if the converter is armed and an external
trigger is not detected.
An external trigger event is detected when the GPIO3 input has an edge that matches the edge detection
programmed in the EDGE bit, at the I2C register ADC_DELAY. The internal ADC trigger can be delayed with
respect to the external trigger signal edge. The delay time value is set by the ADC_DELAY register bits
DELAY_n, and can range from 0
s (no delay) to 750 s. A conversion is started only if the external trigger
remains at its active level when the delay time expires, as shown in Figure 49. In a positive-edge detection the
active trigger level is HI; in a negative-edge detection the active trigger level is LO.
Figure 49. ADC Conversion Triggerd by GPIO3 Positive Edge Triggered Active Level Hi
When executing conversion cycles that require multiple samples it may be desirable to synchronize the input
signal conversion using either an external trigger that has a periodic repetition rate or an external asynchronous
trigger that indicates when the external input signal being converted is valid. The TPS65820 has additional
operating modes and timing parameters that can be programmed using the I2C to configure multiple sample
conversion cycles.
In multiple sample cycles the host can select the wait time between samples using the bits WAITn in the
ADC_WAIT register to set the wait time between samples. The wait time is measured between the end of a
conversion and the start of a new conversion.
70
Copyright 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS65820
相關PDF資料 |
PDF描述 |
|---|---|
| TPS65910RSLT | POWER SUPPLY SUPPORT CKT, PQCC48 |
| TPS65920A2ZCHR | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
| TPS65920A2ZCH | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
| TPS65920BZCHR | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
| TPS65920BZCH | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS658310YFFR | 功能描述:PMIC 解決方案 PMU w/Switching Chgr & Lighting Cntrl RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| TPS65835EVM-705 | 功能描述:電源管理IC開發工具 TPS65835 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS65835RKPR | 功能描述:PMIC 解決方案 Adv PMU w/Integrated MSP430 RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| TPS65835RKPT | 功能描述:PMIC 解決方案 ADVANCED PMU RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| TPS65851ZQZR | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。