- 您現在的位置：買賣IC網 > PDF目錄373970 > AD9886KS-140 (ANALOG DEVICES INC) Analog Interface for Flat Panel Displays PDF資料下載
參數資料
| 型號： | AD9886KS-140 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | Analog Interface for Flat Panel Displays |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| 封裝： | PLASTIC, MQFP-160 |
| 文件頁數： | 29/32頁 |
| 文件大小： | 248K |
| 代理商： | AD9886KS-140 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁
REV. 0
AD9886
–29–
Data is read from the control registers of the AD9886 in a similar
manner. Reading requires two data transfer operations:
The base address must be written with the R/
W
bit of the slave
address byte LOW to set up a sequential read operation.
Reading (the R/
W
bit of the slave address byte HIGH) begins at
the previously established base address. The address of the read
register autoincrements after each byte is transferred.
To terminate a read/write sequence to the AD9886, a stop sig-
nal must be sent. A stop signal comprises a LOW-to-HIGH
transition of SDA while SCL is HIGH.
A repeated start signal occurs when the master device driving
the serial interface generates a start signal without first generat-
ing a stop signal to terminate the current communication. This
is used to change the mode of communication (read, write)
between the slave and master without releasing the serial inter-
face lines.
Serial Interface Read/Write Examples
Write to one control register
Start signal
Slave Address byte (R/
W
bit = LOW)
Base Address byte
Data byte to base address
Stop signal
Write to four consecutive control registers
Start signal
Slave Address byte (R/
W
bit = LOW)
Base Address byte
Data byte to base address
Data byte to (base address + 1)
Data byte to (base address + 2)
Data byte to (base address + 3)
Stop signal
Read from one control register
Start signal
Slave Address byte (R/
W
bit = LOW)
Base Address byte
Start signal
Slave Address byte (R/
W
bit = HIGH)
Data byte from base address
Stop signal
Read from four consecutive control registers
Start signal
Slave Address byte (R/
W
bit = LOW)
Base Address byte
Start signal
Slave Address byte (R/
W
bit = HIGH)
Data byte from base address
Data byte from (base address + 1)
Data byte from (base address + 2)
Data byte from (base address + 3)
Stop signal
BIT 7
SDA
SCL
ACK
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Figure 28. Serial Interface—Typical Byte Transfer
SDA
SCL
t
BUFF
t
STAH
t
DHO
t
DSU
t
DAL
t
DAH
t
STASU
t
STOSU
Figure 27. Serial Port Read/
Write
Timing
相關PDF資料 |
PDF描述 |
|---|---|
| AD9898 | CCD Signal Processor with Precision Timing⑩ Generator |
| AD9898KCP-20 | CCD Signal Processor with Precision Timing⑩ Generator |
| AD9898KCPRL-20 | TVPS00RF-21-41S W/ PC CON |
| AD9901 | Ultrahigh Speed Phase/Frequency Discriminator |
| AD9901KP | Ultrahigh Speed Phase/Frequency Discriminator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9887 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Interface for Flat Panel Displays |
| AD9887/PCB | 制造商:Analog Devices 功能描述:INTRFC DUAL FOR FLAT PNL DISPLAYS 160MQFP - Bulk |
| AD9887A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Interface for Flat Panel Displays |
| AD9887A/PCB | 制造商:Analog Devices 功能描述:INTRFC FOR FLAT PNL DISPLAY 16SOIC W - Bulk |
| AD9887AKS-100 | 制造商:Analog Devices 功能描述:Interface for Flat Panel Display 160-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:DUAL A/D INTERFACE FOR FLAT PANEL - Bulk |
發布緊急采購，3分鐘左右您將得到回復。