欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： AD9992BBCZ
廠商： ANALOG DEVICES INC
元件分類： 消費家電
英文描述： 12-Bit CCD Signal Processor with Precision Timing Generator
中文描述： SPECIALTY CONSUMER CIRCUIT, PBGA105
封裝： 8 X 8 MM, 0.65 MM PITCH, ROHS COMPLIANT, MO-225, CSPBGA-105
文件頁數： 56/92頁
文件大小： 718K
代理商： AD9992BBCZ
AD9992
COMPLETE EXPOSURE/READOUT OPERATION
USING PRIMARY COUNTER AND GPO SIGNALS
Figure 64 demonstrates a typical expose/read cycle while exercising
the GPO signals. Using a 3-field CCD with an exposure time
that is greater than one field but less than two fields in duration,
requires a total of five fields for the entire exposure/readout
operation. Other exposure times and other CCD field config-
urations require modification of these example settings.
Rev. 0 | Page 56 of 92
Note that if the MODE registers are changed to be VD updated,
as shown in the MODE Registers section and in Figure 52, the
MODE update will be delayed by one additional field. This should
be accounted for in selecting the number of fields to cycle and
which VD location to write to the MODE registers.
1.
The primary counter is used to control the masking
of VSG and SUBCK during exposure/readout. The
PRIMARY_MAX register should be set equal to the
total number of fields used for exposure and readout.
In this example, PRIMARY_MAX = 5.
The SUBCK masking should not occur immediately at
the next VD edge (Step 2), because this would define an
exposure time that begins in the previous field. Write to
the PRIMARY_DELAY register to delay the masking of
VSG and SUBCK pulses in the first exposure field. In this
example, MASKDELAY = 1.
Write to the SUBCKMASK_NUM register (Address 0x74)
to specify the number of fields to mask SUBCK while the
CCD data is read. In this example, SUBCKMASK_NUM = 4.
Write to the SGMASK_NUM register (Address 0x74) to
specify the number of fields to mask VSG outputs during
exposure. In this example, SGMASK_NUM = 1.
Write to the PRIMARY_ACTION register (Address 0x70)
to trigger the GP1 (STROBE), GP2 (MSHUT), and GP3
(VSUB) signals and to start the expose/read operation.
Write to the MODE registers to configure the next five
fields. The first two fields during exposure are the same as
the current draft mode fields, and the following three fields
are the still-frame readout fields. The register settings for
the draft mode field and the three readout fields are
previously programmed. Note that if the MODE registers
are changed to VD updated, only one field of exposure
should be included (the second one) because the MODE
settings will be delayed an extra field.
2.
VD/HD falling edge updates the serial writes from 1.
3.
GP3 (VSUB) output turns on at the field/line/pixel specified.
VSUB Example 1 and Example 2 use GP3TOG1_FD = 1.
4.
GP1 (STROBE) output turns on and off at the location
specified.
5.
GP2 (MSHUT) output turns off at the location specified.
6.
The next VD falling edge automatically starts the first
read field.
7.
The next VD falling edge automatically starts the second
read field.
8.
The next VD falling edge automatically starts the third
read field.
9.
Write to the MODE register to reconfigure the single draft
mode field timing. Note that if the MODE registers are
changed to VD updated, this write should occur one field
earlier.
10.
VD/HD falling edge updates the serial writes from 9. VSG
outputs return to draft mode timing. SUBCK output
resumes operation. GP2 (MSHUT) output returns to the
on position (active or open). GP3 (VSUB) output returns
to the off position (inactive).
相關PDF資料
PDF描述
AD9992BBCZRL 12-Bit CCD Signal Processor with Precision Timing Generator
AD9995KCP 12-Bit CCD Signal Processor with Precision Timing ⑩ Generator
AD9995KCPRL 12-Bit CCD Signal Processor with Precision Timing ⑩ Generator
AD9995 12-Bit CCD Signal Processor with Precision Timing ⑩ Generator
ADA4000-2ARMZ-RL Low Cost, Precision JFET Input Operational Amplifiers
相關代理商/技術參數
參數描述
AD9992BBCZRL 功能描述:IC CCD SGNL PROC 12BIT 105CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件
AD9993BBCZ 功能描述:IC MIXED-SIGNAL FRONT END 196BGA 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 類型:ADC，DAC 輸入類型:LVDS 輸出類型:LVDS 接口:SPI 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:196-LFBGA，CSPBGA 供應商器件封裝:196-CSPBGA（12x12） 標準包裝:1
AD9993BBCZRL 功能描述:IC MIXED-SIGNAL FRONT END 196BGA 制造商:analog devices inc. 系列:- 包裝:帶卷（TR） 零件狀態:在售 類型:ADC，DAC 輸入類型:LVDS 輸出類型:LVDS 接口:SPI 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:196-LFBGA，CSPBGA 供應商器件封裝:196-CSPBGA（12x12） 標準包裝:1,500
AD9993-EBZ 功能描述:EVAL BOARD MXFE AD9993 制造商:analog devices inc. 系列:* 零件狀態:在售 標準包裝:1
AD9994 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit CCD Signal Processor with Precision Timing Generator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 漳平市| 布拖县| 长垣县| 浪卡子县| 永吉县| 灵石县| 阿巴嘎旗| 特克斯县| 灵寿县| 襄汾县| 柳河县| 名山县| 始兴县| 奉贤区| 左云县| 广水市| 家居| 宁津县| 阿鲁科尔沁旗| 清镇市| 富裕县| 祁阳县| 和平区| 西丰县| 昌乐县| 习水县| 会理县| 洛川县| 和平区| 永昌县| 科技| 含山县| 青浦区| 平顺县| 巴塘县| 庄浪县| 广州市| 泰兴市| 申扎县| 武汉市| 无锡市|