- 您現在的位置：買賣IC網 > PDF目錄373975 > ADAU1702JSTZ-RL (ANALOG DEVICES INC) SigmaDSP 28-56-Bit Audio Processor with Two ADCs and Four DACs PDF資料下載
參數資料
| 型號： | ADAU1702JSTZ-RL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | SigmaDSP 28-56-Bit Audio Processor with Two ADCs and Four DACs |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MS-026BBC, LQFP-48 |
| 文件頁數： | 22/52頁 |
| 文件大小： | 773K |
| 代理商： | ADAU1702JSTZ-RL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
ADAU1702
I
2
C PORT
The ADAU1702 supports a 2-wire serial (I
2
C-compatible)
microprocessor bus driving multiple peripherals. Two pins,
serial data (SDA) and serial clock (SCL), carry information
between the ADAU1702 and the system I
2
C master controller.
In I
2
C mode, the ADAU1702 is always a slave on the bus,
meaning it cannot initiate a data transfer. Each slave device is
recognized by a unique address. The address byte format is
shown in Table 15. The ADAU1702 slave addresses are set with
the ADDR0 and ADDR1 pins. The address resides in the first
seven bits of the I
2
C write. The LSB of this byte sets either a read
or write operation. Logic Level 1 corresponds to a read operation,
and Logic Level 0 corresponds to a write operation. Bit 5 and
Bit 6 of the address are set by tying the ADDRx pins of the
ADAU1702 to Logic Level 0 or Logic Level 1. The full byte
addresses, including the pin settings and read/write bit, are
shown in Table 16.
Burst mode addressing, where the subaddresses are automati-
cally incremented at word boundaries, can be used for writing
large amounts of data to contiguous memory locations. This
increment happens automatically after a single-word write unless a
stop condition is encountered. The registers and RAMs in the
ADAU1702 range in width from one to five bytes, so the auto-
increment feature knows the mapping between subaddresses and
the word length of the destination register (or memory location). A
data transfer is always terminated by a stop condition.
Both SDA and SCL should have 2.2 kΩ pull-up resistors on the
lines connected to them. The voltage on these signal lines should
not be more than IOVDD (3.3 V).
Rev. 0 | Page 22 of 52
Table 15. ADAU1702 I
2
C Address Byte Format
Bit 0
Bit 1
Bit 2
Bit 3
0
1
1
0
Bit 4
1
Bit 5
ADDR1
Bit 6
ADDR0
Bit 7
R/W
Table 16. ADAU1702 I
2
C Addresses
ADDR1
ADDR0
0
0
0
0
0
1
0
1
1
0
1
0
1
1
1
1
Read/Write
0
1
0
1
0
1
0
1
Slave Address
0x68
0x69
0x6A
0x6B
0x6C
0x6D
0x6E
0x6F
Addressing
Initially, each device on the I
2
C bus is in an idle state and
monitoring the SDA and SCL lines for a start condition and
the proper address. The I
2
C master initiates a data transfer by
establishing a start condition, defined by a high-to-low transition
on SDA while SCL remains high. This indicates that an address/
data stream follows. All devices on the bus respond to the start
condition and shift the next eight bits (the 7-bit address plus the
R/W bit) MSB first. The device that recognizes the transmitted
address responds by pulling the data line low during the ninth
clock pulse. This ninth bit is known as an acknowledge bit. All
other devices withdraw from the bus at this point and return to
the idle condition. The R/W bit determines the direction of the
data. A Logic 0 on the LSB of the first byte means the master
will write information to the peripheral, whereas a Logic 1
means the master will read information from the peripheral
after writing the subaddress and repeating the start address. A
data transfer takes place until a stop condition is encountered.
A stop condition occurs when SDA transitions from low to high
while SCL is held high. Figure 20 shows the timing of an I
2
C
write, and Figure 21 shows an I
2
C read.
Stop and start conditions can be detected at any stage during the
data transfer. If these conditions are asserted out of sequence with
normal read and write operations, the ADAU1702 immediately
jumps to the idle condition. During a given SCL high period,
the user should only issue one start condition, one stop condition,
or a single stop condition followed by a single start condition. If
an invalid subaddress is issued by the user, the ADAU1702 does
not issue an acknowledge and returns to the idle condition. If
the user exceeds the highest subaddress while in auto-increment
mode, one of two actions is taken. In read mode, the ADAU1702
outputs the highest subaddress register contents until the master
device issues a no acknowledge, indicating the end of a read. A
no-acknowledge condition is where the SDA line is not pulled
low on the ninth clock pulse on SCL. If the highest subaddress
location is reached while in write mode, the data for the invalid
byte is not loaded into any subaddress register, a no acknowledge
is issued by the ADAU1702, and the part returns to the idle
condition.
相關PDF資料 |
PDF描述 |
|---|---|
| ADC912A | CMOS Microprocessor-Compatible 12-Bit A/D Converter |
| ADC912AFP | CMOS Microprocessor-Compatible 12-Bit A/D Converter |
| ADC912AFS | CMOS Microprocessor-Compatible 12-Bit A/D Converter |
| ADCMP341 | Dual 0.275% Comparators and Reference with Programmable Hysteresis |
| ADCMP341_07 | Dual 0.275% Comparators and Reference with Programmable Hysteresis |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADAU1761 | 制造商:AD 制造商全稱:Analog Devices 功能描述:SigmaDSP Stereo, Low Power, 96 kHz, 24-Bit Audio Codec with Integrated PLL |
| ADAU1761BCPZ | 功能描述:IC SIGMADSP CODEC PLL 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:SigmaDSP® 標準包裝:2,500 系列:- 類型:PCM 數據接口:PCM 音頻接口 分辨率（位）:15 b ADC / DAC 數量:1 / 1 三角積分調變:是 S/N 比，標準 ADC / DAC (db):- 動態范圍，標準 ADC / DAC (db):- 電壓 - 電源，模擬:2.7 V ~ 3.3 V 電壓 - 電源，數字:2.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-VFBGA 供應商設備封裝:80-BGA MICROSTAR JUNIOR（5x5） 包裝:帶卷 (TR) 其它名稱:296-21257-2 |
| ADAU1761BCPZ | 制造商:Analog Devices 功能描述:IC, AUDIO CODEC, 24BIT, 96KHZ, LFCSP-32 |
| ADAU1761BCPZ-R7 | 功能描述:IC SIGMADSP CODEC PLL 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:SigmaDSP® 標準包裝:2,500 系列:- 類型:立體聲音頻 數據接口:串行 分辨率（位）:18 b ADC / DAC 數量:2 / 2 三角積分調變:是 S/N 比，標準 ADC / DAC (db):81.5 / 88 動態范圍，標準 ADC / DAC (db):82 / 87.5 電壓 - 電源，模擬:2.6 V ~ 3.3 V 電壓 - 電源，數字:1.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-WFQFN 裸露焊盤 供應商設備封裝:48-TQFN-EP（7x7） 包裝:帶卷 (TR) |
| ADAU1761BCPZ-RL | 功能描述:IC SIGMADSP CODEC PLL 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:SigmaDSP® 標準包裝:2,500 系列:- 類型:立體聲音頻 數據接口:串行 分辨率（位）:18 b ADC / DAC 數量:2 / 2 三角積分調變:是 S/N 比，標準 ADC / DAC (db):81.5 / 88 動態范圍，標準 ADC / DAC (db):82 / 87.5 電壓 - 電源，模擬:2.6 V ~ 3.3 V 電壓 - 電源，數字:1.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-WFQFN 裸露焊盤 供應商設備封裝:48-TQFN-EP（7x7） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。